RB1005XYW2 Whirlpool Wall Oven - Instructions

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

After unpacking and checking the unit that was mailed to me, I cleaned the ends of both the connections in the oven and the connections on the part, then plugged them together and screwed the plates in place in the oven. The oven worked immediately and still is working very efficiently. I had no problems at all with the installation.

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

The old part, including lightbulb and socket, had corroded into place, and the glass light cover was stuck to the socket. I used a dead blow hammer and a dowel just under the diameter of the hole to tap on the back side of the socket to loosen it and get it out. The metal tabs on the old socket were folded back to make it fit better (?), which made it harder to remove. Lots of muscling of the part to get it out. Easy to install new part once old one was out of the way. An experienced person would have removed the old part and installed the new in no time.

I trouble shot and traced out to electrical short in face panel and found burnt wires. I've been a licensed electrician for years and it takes alot of comon sense to trouble shoot and find problem. I found schetch-matic of appliance and searched computor and found partselect.com and tried it. It wasnt no time and the part was at my door. Thank you partselect and i would use them again in the future. billy

Replaced the oven light with a new one but it burnt out as soon as I turned it on. Therefore I decided a new socket may help.

My whirlpool apparently has the old style socket which is pictured in partselect part #PS12584564. The old style socket has to two metal arms that retain it against the metal reflector.

The part that will come (#PS12584564) however is the new style that whirlpool has changed to, apparently. It is not as pictured. The socket and the reflector have different retention devices.

I used screw drivers to bend the two metal arms away to release the socket. Then I had to use allen wrenches to bend the reflector's retention tabs away.

Once I had the old socket, reflector, and lens replaced I just followed the video on partselect for part #PS12584564

I killed the circuit breaker to the oven, then double checked with an electrical tester. I removed the oven door for easy access, unscrewed the element bracket screws, plugged in the new element and then I reversed the steps above.

I am very happy with PartSelect and will use them in the future for all my appliance parts needs.

removed old burned out element, installed new element

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!

My son is very handy. He had no trouble installing the new heating unit. The new part seems to be working well.

Pop old one out and new one in

After figuring I'd have to buy a new oven, I figured out that it was the lower baking element. When I received the new part, I removed the two screws holding the element on. Gently pulled the element off the back oven wall and removed the wire connectors. Put the new element in place - rehooked the wire connectors and it works like new. The light bulb replacement was as simple as screwing in the new light bulb. Thanks, saved me alot of money.....

The part came as promised & and it was exactly the right part! I turned off the breaker to the oven (the oven has a clock and timer on it too). Unscrewed the 2 screws with a Phillips screw-driver and carefully removed the old part - being very careful to be safe and not make a big mess. It was easy to disconnect the wires and get the old element out. Then connected the wires to the new element, placed into position, screwed in the 2 screws, and turned on the breaker. It worked great. Then set the clock because it was 13 minutes slow!

turn off electric breaker, unscrew the 2 screws unplug the 2 ends replace old element with new repeat previous steps but unfortunately the control panel was also failing and that item has been discontinued.