GBD307PDT4 Whirlpool Wall Oven - Instructions

1) Removed the trim pieces (2 screws). 2) removed the 2 screws holding the oven in the wall. 3) Slid the oven out of the wall cabinet 4) removed the back panel of the oven ( 10 screws. 5.) removed the old thermostat (2 nuts) 6.). Installed the new thermostat and reversed steps 4-1

1. Disconnect AC power 2. Remove back with several sheet metal screws. 3. Remove wires from Limit Thermostat. 4. Check Limit Thermostat continuity -- if open then Limit Thermostat is faulty. 5. Remove Limit Thermostat with two screws. 6. Install new thermostat

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

Removed locking device

Followed suggestions from prior Customers that had same problem.

The oven is a KitchenAid convection oven with 4 panes of glass. The front, two inner glass panes that aren’t “touchable” and the interior glass that is the one that takes the heat from the oven and which you can clean easily - this is important because the descriptions of the glass all say “inner glass”. This is door #3 in the diagram that measure 10 x 22”. Which I cracked when I was pouring water into a pan to create steam for bread baking (lesson learned).

Because of the age of the oven, to remove the oven door it was necessary to place “pins” (we use medium screws) into the hole behind the door latches. Then were able to lift off the oven door. (We saw some videos on YouTube)

We placed the oven door on the counter top and removed ALL screws that held the door at the bottom and around the casing - KEEP these screws separate by where you’ve removed them so you replace them into the proper section when you reassemble the door. Each glass you remove has slots that hold them in their proper places. I recommend taking a picture BEFORE you take out each glass as there are brackets that need to go in proper order and you don’t want to forget the order.

We had to flip the door over in order to CAREFULLY remove the casing and access the different inner glass sections (took the opportunity to really clean them). Gathered the broken glass pieces into a paper bag and vacuumed the fragments. Then we were able to place the new interior glass from PartSelect, and reassemble the oven door. It’s perfect!

This took some time most likely because it’s a very old oven and you need to be methodical. I was just glad to be able to get the part - not yet ready to replace the oven.

BTW, originally I was guided to order glass #7 which is one of the inner glass panes that you cannot touch - unless you take apart the oven door - The exchange for the proper door was handled very quickly and easily. Hope this helps.

I turn off the power in the breaker box and then unscrew the part and replace it with the new one

Pulled the stove out, unscrewed the back and plugged the new thermostat in. Screwed the back back on

unscrew cover
remove old bulb
screw in new bulb
replace cover

Well, the instructions on the computer site were very easy to understand, however, the difficulty lay in the fact that we were 2 78 yr old people and getting to the inside the oven, lifting up the element so that we could see where it should be connected and get it connected was a task. We had to get down on our knees and then get back up. That was a chore within itself. But, the instructions were easy and clear.
Bottom line if us old people can do it, anyone can.

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.

After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.

Removed the small metal panel covering the main power terminal in back of the electric range. Removed the nuts holding the red, white and black electrical wires from the range using the appropriate socket (there will be two nuts on each bolt end). Removed the two screws holding the main power terminal block with appropriate screw driver. Connect the new main power terminal block to the range using the two screws. Reconnect the red, black and white electrical wires coming from the range using one nut for each wire. IMPORTANT: do no over tighten the nuts because the bolts could snap. Reconnect the pigtail and secure the small metal panel covering the main power panel.

removed door from oven, took all screws off door to remove glass, put new glass in place, put oven door back together, put oven door back onto the oven