RBD275PDB2 Whirlpool Wall Oven - Instructions

With some help from my wife.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

replace thermal safety switch on back of oven

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Removed the old element by taking out two screws and replaced the new unit using the same screws. The delivery time on the new element was very quick-about two days. Thanks.

Ordered the part from partselect.com. I was amazed that it arrived the next day! It was the easiest repair I ever did. Took out 2 screws, unplugged the wires from the old element, plugged the wires into the new one, and replace the screws. Done.

Went to PartSelect on the internet and looked up my model. Next I selected the problem from a short list of questions, which indicated the broil element was the problem 99% of the time. With this bit of confidence I ordered the part which was delivered in 2 days. The first step in the repair was to turn off the circuit breaker for the oven. After removing four screws that held the broil element in the oven, I pulled the electrical connectors apart on each end of the old element and attached the new unit to the electrical leads. Lastly I pushed all the wiring back inside the back wall of the oven and replaced the four mounting screws. I then performed ops check, which worked. End of story, job done in about 10 to 15 minutes. Easy Peasy.

Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.

Turned off circuit breaker. Unscrewed two screws, although they required a square tipped screwdriver insert which I fortunately had phone estimates for this job were between $150 - $180. Could not have been easier.

Once the door was secured with hinge locking pins which I made out of cut off 16 penny nails,I removed the door , layed it on a soft padded piece of vinyl and proceeded to remove the inside top cover which was secured with phillips screws on the top and sides. I was then greeted by 2 sheets of glass before I could get to the front glass which was the one that cracked.These sheets of glass were secures with slotted metal frames which also required removing several screws and braces. I was then able to remove the cracked glass and replace it with the new glass panel. Then I had to reverse the steps to assemble the door which was fairly easy since I made a diagram of the steps when I disassembled the door (this saved me alot of aggravation since my memory isn't what it used to be. The door was fitted into the frame of the oven and once the hinges were in place I removed the pins and closed the door. It was at that point that I got a kiss from my grateful wife. End of story.

I am not a big do-it-yourselfer, so maybe I might have found this more difficult than expected. When I first looked at the oven before ordering the part, I saw a couple of screws and it seemed like an easy task. However, I found that I had to remove to whole door first, which was actually easy. Then I started to remove the case. Then I removed several layers of a puzzle. Oven door had 3 pieces of glass and 3 metal brackets. The installation video was for a completely different oven. Although I got out the broken glass easily, I had difficulty reassembling. The oven diagram for the parts was even deceiving. I had to involve my spouse and after an hour of cursing everything, we finally managed to get the thing back together. Whoever designed this oven must have been a deranged German scientist. However, everything is back to normal and I probably saved a couple hundred bucks for a repairman.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.