RB1005XYN3 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Granite Falls, NC
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
My heating element had been melted through by some type of food and was severed into 2 metal peices. It could no longer be used without dangerous consequences.
I got my part in the mail and FIRSTLY, unplugged the entire stove from the wall. I unscrewed the old part from the front, took the panels off the back, and disconnected the element from the yellow and red wires.I removed the old part completely from the stove. I then put the new part in, reconnected the wires, screwed the part into the oven, then BEFORE putting the back paneling on, I tested it. The new element works like a dream. I then, put the paneling back on & was finished!
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
BE SURE WHEN YOU BUY TO CHECK WATTAGE OF YOUR OVEN TO YOUR ELEMENT. Voltage doesn't matter because most voltage is the same in any house you live in...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Midland, TX
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
bae element burned out after 22 years.
Easiest repair I have ever done.
Removed two screws and pulled element out, exposing wiring. Pulled wiring connection apart with pliers. Attached wiring to new element and inserted element back in place and replaced screws. All done!!!
It worked.
Removed two screws and pulled element out, exposing wiring. Pulled wiring connection apart with pliers. Attached wiring to new element and inserted element back in place and replaced screws. All done!!!
It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- pauline from newport news, VA
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would't heat
First removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...then replaced the old element with the new element..........(worked perfectly)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- W Pendleton from Cumming, GA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
After 12 years the element died for the 2nd time We thought about getting a new oven, but ours has become sort of "retro" looking. I think it's from the '60s. We looked on line and found the part at a reasonable price and decided to give it a try.
I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terrence from New Cumberland, PA
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Baking element not heating
Replaced element.
Looks like I saved at least 500$
Geuss I'm Winning!
:)
Looks like I saved at least 500$
Geuss I'm Winning!
:)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Eufaula, OK
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inoperative heating element
Opened circuit breaker, unscrewed old element, disconnected old heating element wire, attached new element wire, screwed new element into place, closed circuit breaker. tested element for heat.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Cottage Grove, MN
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element burned out and cracked
Removed two screws, removed two clips, removed the element and rehooked the two clips and screwed the two clips back in. Zip Zip.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Vassar, KS
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven quit heating
My daughter told me here oven had quit and ask my advice. I saw where the element was burnt. Took out 2 screws unkooked the wires. I was unable to get help at the local Appl repair store so I went to internet to parts select.com I put in model # and had the part within 3 days put it back in and worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GARY from HARRISBURG, IL
- Parts Used:
- 326791
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bake Element
Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brett from Huston, TX
- Parts Used:
- WP660579
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Broiler Element broke
Unscrewed 4 screws holding element. Disengaged one wire, but 2nd one was separated while pulling through rear wall. Could not grasp the wire from the front. Then unscrewed 4 screws along sides of oven to pull casing away from wall cavity. Sat oven on a box while unscrewing 12 rear panel screws. Pulled wire through from back into oven. (Didn't need to do this because new element extended through the rear wall to access from back. Could have reattached wires to new element from the rear, but didn't realize this soon enough.)....two days later reinstalled new broiler element reattaching wires inside the oven and replacing 4 screws holding element in the oven. To replace the back panel I had to lay oven on its face so the holes on back of would fit with the rear panel. Put 12 screws back on. Then pushed oven back into wall cavity and put 4 screws holding oven in place. It is now working!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donna from Dacoma, OK
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broiler element went out in my oven
Fast shipping and the part was very easily installed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from St Louis, MO
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
oven not heating on "Bake"
I observed that the lower heating element was attached to the lower rear of the oven by two stainless phillips screws. I removed the screws and gently pulled the element outward. The element came out easily with two large red wires attached (one on each side). I unplugged the wires and extracted the old element. I used this as an opportunity to clean the floor of the oven that was hard to get at with the element in place. I installed the new element by plugging in the two red wires and used the same two stainless screws to reattach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOHN from SIOUX FALLS, SD
- Parts Used:
- 326791
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
element didn't heat
Easy as 1, 2, 3
Was this instruction helpful to you?
Thank you for voting!