GBS307PDB0 Whirlpool Wall Oven - Instructions

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??

Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.

Replaced hinges since weak springs were allowing the door to open as the oven heated which would turn on the oven light and give a warning on the control panel. To remove door you need to open the dorr all the way and place a short pin through a hole in the hinge under the hinge point. The pin needs to be short enough that you can get it to pass through the door surround. I cut a short pair of pins from a 16D nail. Place the short pins in the respective hinges and then close the door. Grip the oven door handle and the bottom of the door and lift it free of the oven. Lay the door face down on a towel or blanket. remove three phillips screws from the top of the door and two from the brackets on the bottom of the door. Also can remove the two phillips screws on the door that hold each hinge in place. Seperate the door from the glass and lift out the old hinges. Install the new hinges and reassemble the door. ILift the door back into place. Make sure you install it tight/close to the oven front. Open the door, noting any interference and if it opens freely then open completely and remove the factory installed pins from the hinge and you should be done!

With some help from my wife.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

Lower the oven door. Insert the locking hinge pins. Pull the door away from the oven. Remove the 4 screws, 2 at the top and 2 at the bottom, to remove the front panel. Remove the 4 screws that secure each left and right spring. Remove the old springs and install the replacements by reversing the procedure. Remember to purchase 2 springs.

You need to replace both the left and right springs. Open the door completely, . Insert a short screw in each pin hole on each spring bracket.slightly lift the door and pull out. remove the four screws that secure the front panel. Remove the four screws that secure the springs. Install the new springs and replace the front panel. Replace the door assembly into the oven, remove the pins that were shipped with the hinges and you are done.

1. REMEMBERED TO SHUT OFF THE APPLICABLE 240V BREAKER. 2. Carefully removed the 2 screws holding the element to the oven structure 3. Carefully extracted the 2 wires from the holes at the rear. 4. Carefully removed the wires from the old element 5. Attached the wire sockets to the new element. 6. Carefully eased the wires back through the holes at the rear 7. Attached the 2 screws through the element holding clamp to the rear wall of the oven. Everything went better than I had expected.

First thing- Don't be afraid! It took me way longer to clean the old door parts than to do the actual replacement. First take the door off by opening it fully and sliding a round piece of metal ( I used a 16d nail) in each hinge mechanism. close the door about 3/4 of the way and pull up. Th door comes right off. Just keep undoing screws until you get down to the layer of glass you need to replace, then reverse the process. If you're replacing both the hinges, note that both the pins used to hold the hinge open come out the right side.

Turned off circuit breaker. Unscrewed two screws, although they required a square tipped screwdriver insert which I fortunately had phone estimates for this job were between $150 - $180. Could not have been easier.

removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.