RB100PXYB0 Whirlpool Wall Oven - Instructions

I first went to the breaker box and shut off the power to the oven.
Then I pulled the 2 screws from the back of the oven that held the element in and pulled off the clips and removed the old element.
My wife decided to give the old oven a good cleaning with a non-fuming cleanser while I went out to play golf.
When I came home she had applied the 2 clips to the new element and fastened it in with the 2 screws. (I love it when women use tools!)
The oven now looks and works like new!

Replaced element.
Looks like I saved at least 500$
Geuss I'm Winning!
:)

Opened circuit breaker, unscrewed old element, disconnected old heating element wire, attached new element wire, screwed new element into place, closed circuit breaker. tested element for heat.

Removed two screws, removed two clips, removed the element and rehooked the two clips and screwed the two clips back in. Zip Zip.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

very easy

My daughter told me here oven had quit and ask my advice. I saw where the element was burnt. Took out 2 screws unkooked the wires. I was unable to get help at the local Appl repair store so I went to internet to parts select.com I put in model # and had the part within 3 days put it back in and worked fine.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Unscrewed 4 screws holding element. Disengaged one wire, but 2nd one was separated while pulling through rear wall. Could not grasp the wire from the front. Then unscrewed 4 screws along sides of oven to pull casing away from wall cavity. Sat oven on a box while unscrewing 12 rear panel screws. Pulled wire through from back into oven. (Didn't need to do this because new element extended through the rear wall to access from back. Could have reattached wires to new element from the rear, but didn't realize this soon enough.)....two days later reinstalled new broiler element reattaching wires inside the oven and replacing 4 screws holding element in the oven. To replace the back panel I had to lay oven on its face so the holes on back of would fit with the rear panel. Put 12 screws back on. Then pushed oven back into wall cavity and put 4 screws holding oven in place. It is now working!

I oedered a new unit matched with the Model Number! Installed .It did not work.They said Part amybe defectice.They quickly sent out another.That was installed and did not work.I contacted them again and they sugessted the Modular unit that regulated the Heat Temp. They were discontinued. They suggested I contact Corecentic Solution.com which I did.I am now in the process of shipping out my Modular Element to have it rebuilt. My stove is over 20 Yrs old .It inly costs me $110.00 to fix ourselves. Thank YouParts Select.com. You saved me over $1700.00 It would have cost to buy a new stove. They also gave me a full refund on the two units they shipped out. They are a wonderful helpful Company and will take care of your parts needs. Thanks Again Joyce

Turned off power to unit onswitch box. Used Phillips screwdriver to take out old unit.Could come out at least 3"with connecting wires with clips on their ends. Disconnected clips ,connected clips to new unit and put back in place. Redid screws. Turned on power.... Wa-La ... Works Great. Thank You Very Much for your service.

Fast shipping and the part was very easily installed.

The element comes with the element attached to the bracket that holds it in place in the top of the oven. I had removed the 2 screws-one on each side--on the old element and disconnected the spade connections on the wiring after I pulled the element out far enough to expose them. I then reconnected the new element, pushed it back into place and re-installed the screws that hold it in place. A pretty simple job but I got a tremendous feeling of accomplishment after it was done. Saved a bunch of $$$ also!!