RB266PXV1 Whirlpool Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharon from Redding, CA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element caught on fire!!
My husband is an over-the-road driver, so I have to do all of the repairs myself. I went to the breaker box and turned off the power to the range. Then I removed 2 screws, pulled the element out about 3", and disconnected the wires. I then connected the wires to the new element, pushed it back in place, and replaced the screws. We had Parmesan Chicken for dinner and my children were thrilled!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronica from Brunswick, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bottom element was burned out
I removed two screws, pulled it out a few inched and unpluged two wires. I then plugged the two wires into the new element slowly slid the wires and element back into place and put the two screws back in... and it worked perfectly. I did it all in less than five mins. And I am a 53 year old woman.No man was required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christopher from Arlington, NE
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
When the oven was on we noticed the bake element had a 1 inch section that was bright red. Upon closer inspection, after the oven was off and the element cool, corrosion like damage was apparent where the element had been bright red.
Naturally the oven turned was off but for added safety I also set the breaker protecting the oven to the off position. Where the element attaches to the oven there is a small plate with two screws holding the element in position. Remove these two screws and then gently pull the element out 2-3 inches, which will expose the electrical connection. Using needle nose pliers gently pull on one of the wires to remove it from the element. Now remove the other and discard the old element. Simply plug the new element into those wires and screw the plate back into the oven. Now turn the breaker back on and you're done. Super easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Raymond, NH
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
items in the oven were not baking properly. We discovered the bake elemnent wasn't working and looked defective in one part.
I removed the back panel, unplugged the wires, removed the 2 screws, replaced the element, plugged the wires back in and put the back panel back on. Now that I'm thinking about it, I guess I didn't even need to remove the back panel to replace the element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from WOODSTOCK, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Oven didn't get over 300 deg. F.
Removed old element, replaced new element. Unfortunately, this didn't fix the problem. It was the temperature sensor. But now I have a new bake element, though!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from OLIVE BRANCH, MS
- Parts Used:
- WP660579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Top broiler element busted
Piece a cake!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!
Turned off electrical breaker.
Removed original screws from old defective element and slipped in new replacement element.
Perfect fit!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from MIDDLE RIVER, MD
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out
Turn off the oven circuit breaker. Remove 2 screws that hold the element in place. Carefully pull element out, about 3 inches and remove 2 attached wires by holding the element and pulling the wire clips off of the old element. Slide wire clips onto the new element and put the screws back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carolyn from ROGERSVILLE, TN
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element was broken
was very easy to install I only needed a phillips screwdriver to remove old part and install new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from YONCALLA, OR
- Parts Used:
- WP308180
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven Heating element had a melt down and small explosion
Remove racks, extract two phillips head screws, pull out element, unattached wires, install new element, reverse procedure to complete installation. (Note: With the racks and element out, great time to clean oven.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Diane from Olathe, KS
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element burned out - Easy repair
Took a phillips head screwdriver and took out the two screws. Lifted off small plate securing screws, pulled lightly and wiggled the element out and popped the new one in. Total time 7 minutes - yes we timed it!!! Fast delivery too!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth from HOUSTON, TX
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
wire came loose and shorted out
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Elcho, WI
- Parts Used:
- WP3169203
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Replaced inner oven glass and reconnected the self cleaning lever.
The replacement of the glass was easy, I removed the door and placed on work bench. As long as you lay the parts out in an orderly manner the reassembly goes pretty good. The longest time was cleaning the glass's that were dirty from the inner broken glass.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.
I also reconnected the self cleaning oven lever this required the removal of the oven top. Lot of screws to remove but went ok. I put locktite on the two screws which are extremely short.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from Kirkland, WA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the old element done broke....
my wife took the old element out i used a screw driver to remove it...i then ordered the new part using this web site...i then let my wife install the new element she then attatched the wires she used her fingers to tighten the bolt....and she is very very impressed with herself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from Snellville, GA
- Parts Used:
- WP308180
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake element sparked & smoked, then wouldn't work.
Turned off circuit breaker for oven. Unscrewed the 2 screws that held the element in place on the back wall of the oven. Save those screws! Pulled the element out from the wall. Disconnected the 2 wires. Attached the wires for the new element and then screwed the new element into the back wall. Flipped the circuit back on and the oven was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Moore, SC
- Parts Used:
- WP308180
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven not heating with bake element, broil element working OK.
Locate and shut off 220 volt breaker to Stove/Oven. Remove baking racks from oven. Use phillips screw driver to remove two phillip head screws holding bottom baking element in place. Slowly pull out element/wires and use volt meter to check for presence of voltage. Remove wires from element by pulling off female spade connector, push wire connector onto new element, carefully push wiring and element end thru rear opening and secure with the two phillip head screws. Replace baking racks, turn 220 volt source back on and test element to a high temperture, leave oven door open, new element will smoke slightly and create a burning odor, so take a few minutes to break in the new element. You're now readly to bake.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.
If you don't have a volt meter, turn stove/oven "ON" with lights indicating that stove/oven is ON, turn circuit breaker off and watch indicator lights go "OFF" when circuit breaker is tripped.
Was this instruction helpful to you?
Thank you for voting!