GBS307PRS02 Whirlpool Wall Oven - Instructions

Ordered the part from partselect.com. I was amazed that it arrived the next day! It was the easiest repair I ever did. Took out 2 screws, unplugged the wires from the old element, plugged the wires into the new one, and replace the screws. Done.

Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.

Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.

unscrewed the top glass protector off and took the old bulb out and put the new bulb in. very easy - less than 5 minutes.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

Visited PartSelect.com and ordered the element. Talked to a really sweet lady who assisted me at the company by ordering the part. Received the part and my husband cut off the electricity to the stove, took off the old element, got the sockets and after pushing on the new element, and he screwed the screws back on, cut on the electricity and we cut the stove on and it was ready to go. VERY, VERY SIMPLE TO REPAIR.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

I followed the step-by-step instructions from Steve on the part select videos posted on Youtube.

Took out the 2 screws and removed 2 wires connected to old element, put on new one. Did this all in about 5-10 minutes. Hubby didn't even have to help!

Instructions were clear and the work was easy. Take your time and think about what you are doing, and you won't have any problems replacing the glass.

I took the door off the hinge, laid it on the kitchen island and began to unscrew the outside screws. Be sure to have a bowl to place all the screws so none fall to the floor. I would recommend taking pictures with a camera phone as you dismantle each piece. The extra time was spent trying to remember how to put the 4 panes of glass back together....and if I had pictures to refer to it would have been easier. SECOND TIP- DO NOT have your husband help with any of this. I probably could have finished in less than 30 minutes if I was doing it by myself. Once he went to bed, the reassembly was much easier.

I did not remove the door. After removing as much broken glass as possible, I removed the two screws at the bottom of the door, pushing a bit against the plastic oven vents so the screwdriver could fit into the screw heads. I then removed the two screws on top of the oven door. This releases the outside of the door. I then removed the two bottom screws holding the bracket that holds the piece of glass fitting into the slot at the top. I bent back the tabs with pliers, cleaned the last bit of glass out of the slots, and then put the new glass in and bent the tabs back as much as possible. It actually was pretty tight. The rest is just cleaning and putting the pieces back together. Just be careful as the four screws that go into the top and bottom of the door are actually different from the other screws. Just make sure you keep all screws separated and use them as removed. Not too bad, just time consuming.

I used the manufacturers' manual as a guide and removed the door. This was not straightforward because the diagram was overly simplified. Once I figured it out, door removal was quite easy. I then took the door apart layer by layer (there are several), cleaning each part with oven cleaner, or detergent as I went. If not for cleaning, the repair would have taken half the amount of time. I then put the door together again and re-attached it. This was a little bit tricky but I got it to snap into place on the second attempt. Overall, this is a fairly easy repair and I do not have too much to add to existing comments. I would add the following: (1) Use work gloves to remove the broken glass. In fact, use gloves to handle all glass. (2) Take your time when re-assembling the door because the layers have to be lined up accurately for the screws to take and hold all of the layers together. In summary, I am very pleased with how this repair went. For 90 minutes of my time and $45, I was able to get the oven looking like new again.

find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.

This 60 y.o. female had no owners manual. I completely relied on the information of this forum. *Recommend having a work area prepped before starting. I used a thick beach towel on the kitchen table. A layer of newspaper to catch all the dirty bits is a good idea.*You must remove the door - I followed the instructions using the allen wrench in the holes of the hinge. Open door. I put the short end of the wrench in the hole and leaned the long end against the oven rim. Start closing door and when almost closed, lift up to remove.*Place door handle side up on work surface to remove the 4 screws that hold outermost glass in place, 2 at top and two in brackets at bottom. Lay this aside in safe place on table. *Take off each layer to reach broken glass. *The hinge assembly has to be removed and the allen wrenches have to come out in order to accomplish this. Squeeze the hinge to take pressure off wrench to remove. Gloves help protect your hands for this step.Remove 2 screws each side. Keep each hinge next to the side it came from so you reassemble correctly.*If you have a phone with photo capability - I recommend you take a photo of each disassembly step. This saved me when it came to replacing the two brackets that hold the inner two pieces of glass. Clean all parts before reassembly (this takes the longest amount of time). I placed a thick cup towel in my sink and scrubbed. The cleaner I use for my glass range surface worked best. Dry thoroughly. When you get to the shattered glass remove it very carefully to avoid damaging the insulation underneath. I wish I had just purchased replacement insulation. Once the glass is replaced, everything goes back in reverse order. Now, here's the thing. I spent alot of time scrubbing. So, by the time I got to reassembly, I was bamboozled by the two 10 inch aluminum brackets that hold the two inner pieces of glass in place. So, to avoid any confusion, pay close attention to how these two brackets are placed or take pictures. This was an easy fix that went really well thanks to all the helpful info found here.