RBD275PDB8 Whirlpool Wall Oven - Instructions

Turn off power at the breaker panel; remove oven door (see instructions in owners manual) and racks. Take out the 2 screws holding the element to roof of oven; next remove the 2 screws attaching the element at the rear of the oven; pull out element and disconnect wires. Attach new element to the wires and replace the 2 screws holding element to roof of oven. Next replace to 2 screws attaching element to the rear wall. Replace oven racks and door and turn power back on.

removed two screws in rear of oven. pulled old element out replaced new one. piece of cake.I am a 70 year old female. if i can do it anyone can.thank you for your swift delivery.

Turned off circuit breaker. Unscrewed two screws, although they required a square tipped screwdriver insert which I fortunately had phone estimates for this job were between $150 - $180. Could not have been easier.

Went to PartSelect on the internet and looked up my model. Next I selected the problem from a short list of questions, which indicated the broil element was the problem 99% of the time. With this bit of confidence I ordered the part which was delivered in 2 days. The first step in the repair was to turn off the circuit breaker for the oven. After removing four screws that held the broil element in the oven, I pulled the electrical connectors apart on each end of the old element and attached the new unit to the electrical leads. Lastly I pushed all the wiring back inside the back wall of the oven and replaced the four mounting screws. I then performed ops check, which worked. End of story, job done in about 10 to 15 minutes. Easy Peasy.

The only difficult part of this repair was figuring out how to get the oven door off. Most instructions advise you to flip the hinge locking clips, then lift off the door. But this oven does not have hinge locking clips. What it has is holes in the hinges, just behind the hinge pins. To get the door off, you need to open the door and insert some 3/16' pins in those holes, then close the door and lift it off. I almost got this right the first time, but I used 1/8" pins, and they didn't work, too small. It took me a long time to figure out to use bigger pins. Once the door is off, it's just a few Philips screws to work your way down to the glass. There are 4 layers of glass in this door.

I read all the repairs. Turned off power to oven. Was ready to clamp clips so the don't fall behind oven and Crap!! One clip popped off so easy, it went behind insulation. Had to pull oven out. Put wire through, connected everything. Turned power on and oven and broiler work great.

By reversing the way I removed the door hinges from the frame, per the reinstall instructions. I called the 800# and they emailed me a diagram, but the hinges depicted were different than mine. When my back feels better, I'll keep trying.

Did not want to remove the pin from the new hinges, so found a proper rod and cut off two half inch pins to use in removing the door. followed the manual instructions. Took all of the screws out but did not notice that the four inside face screws were machine screws while all others were sheet metal screws. Had a little difficulty in getting the four machine screws to engage the bottom holes of the new hinges. Reinstalled the door and all works fine. It is too bad that we could not purchase just a new hinge spring instead of the entire unit. It is kind of a waste. I suspect that self cleaning ovens generate a very high heat which eventually weakens the hinge. The upper oven will likely fail in the future, but at least I know how to repair it.

Removed trim strip from each side of oven, removed one screw from each side hat held oven in place and slid oven out of wall. Finally found the thermostat located on the back side of the oven after removing the sheet metal on back. replaced the thermostat and reversed the procedure. Only difficult part was locating the thermostat. I thought it was on top, when in fact it was on the back. Pretty easy, really, and saved some cash in the process.