RB1200XKW2 Whirlpool Wall Oven - Instructions

Piece of cake. Removed door and racks, screwdriver to remove element. Reversed operation and back in service in no time. Good as new. Thanks.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

The element comes with the element attached to the bracket that holds it in place in the top of the oven. I had removed the 2 screws-one on each side--on the old element and disconnected the spade connections on the wiring after I pulled the element out far enough to expose them. I then reconnected the new element, pushed it back into place and re-installed the screws that hold it in place. A pretty simple job but I got a tremendous feeling of accomplishment after it was done. Saved a bunch of $$$ also!!

remove two screws at rear of heat element unit. gently pull element to expose wires connected to heat unit. pull connectors apart on each end (don't let wire slip back into wall hole). connect new unit to wires, insert back into holes and replace screws into back wall of oven. Done... Now that I have done it once, it would now take less than 15 minutes.

The only problem we had was hanging on to the small screws that held the element up. No power screw drivers, so it took a little while to keep a hold of those screws. Considering we are 87 and 84 we feel great that we were able to replace both the bottom element and the broiler. I like the stove, and preferred not to shop for a new one. "Thanks for prompt great service and the video helped. Patty Montag

I oedered a new unit matched with the Model Number! Installed .It did not work.They said Part amybe defectice.They quickly sent out another.That was installed and did not work.I contacted them again and they sugessted the Modular unit that regulated the Heat Temp. They were discontinued. They suggested I contact Corecentic Solution.com which I did.I am now in the process of shipping out my Modular Element to have it rebuilt. My stove is over 20 Yrs old .It inly costs me $110.00 to fix ourselves. Thank YouParts Select.com. You saved me over $1700.00 It would have cost to buy a new stove. They also gave me a full refund on the two units they shipped out. They are a wonderful helpful Company and will take care of your parts needs. Thanks Again Joyce

First, turn off the breaker to the oven, then turn off the service disconnect to the whoe house. I play safe.) Open the door, pull out the oven racks to allow space. Using a Phillips screw driver, unscrew the screws near the front of the oven to loosen the element. Using both hands, pull the element straight out of the holes in the back of the oven, where you will find electric wires attached to them. Pull the ends of the element off the wire connectors. Throw it away. Get you new element, attach the element ends to the connectors. Raise it up to the top of the oven and screw the screws back in to the holes in the top of the oven. You are finished. (The only reason this took me 30 minutes is because I am an old 79 year old granny and can't bend so well, or see so well. I had to use a little acrylic paint on my finger tips to mark the screw holes, it was taking too long to find them the old way, by feel.) GG

Four screws hold the broiler element. I removed the two at the top, then removed the two screwed to the back keeping the element in place. I slowly pulled the element forward and used alligator clips to keep the wire connectors from falling back behind the oven. I disconnected the wires from the broken element and replaced it with the new element. I removed the alligator clips. I screwed the two screws on the back and the two on top and I was finished. Problem solved.

Easy as 1, 2, 3

The part arrived in less than 2 days. I turned off the main electrical switch to the house. All that had to be done was remove two connecting screws in the back of the oven holding the heating element in place. Then I removed two connecting wires with needle nosed plies. I reversed the process with the new element, turned the power back on, and the element heated up and back in business. This was the easiest I have ever had repairing or replacing anything. The hardest part of this repair was finding a flashlight in my house that had good batteries!! Thank you for such quick and courteous service.

we replaced with the appropriate part from Part Select. The agent on the phone was extremely helpful with finding a part for our old oven.

turn off the oven breaker - unscrew both sides of element, pull through holes & remove wire ends. Replace with new element, reversing procedure - turn on breaker & you're good to go.

Turned off power to unit onswitch box. Used Phillips screwdriver to take out old unit.Could come out at least 3"with connecting wires with clips on their ends. Disconnected clips ,connected clips to new unit and put back in place. Redid screws. Turned on power.... Wa-La ... Works Great. Thank You Very Much for your service.

Fast shipping and the part was very easily installed.

First removed the oven door for easy access, removed two screws holding the element pulled old Element from back of oven to expose two connecting wires, disconnected wires and removed old Element. Connected wires to new Element pushed Element back into place and replaced two mounting screws put oven door back on, took about ten minutes. Very Easy!