GBS307PDB8 Whirlpool Wall Oven - Instructions

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

Turned the circuit breaker off, removed trim and the oven screws, pulled oven out, and placed on a stand in front. Electrical cord was just long enough without disconnecting. Removed the back panel, installed the old thermostat with the new one the same way. Used the same phillips screwdriver for the operation. Installed the oven using reverse order. Turn circuit breaker on, back in business. Prior comments definitely helped me a lot. Thanks.

With some help from my wife.

re thermostat/fuse breakage after cleaning: I replaced the part a 2nd time within a year, both times after a cleaning cycle and after 10 years of no similar problem . This time, when putting the oven back, I cleaned all around the door frame and noticed the exhaust grill was heavily filled with dust strands. It's possible this reduced the exhaust enough to overheat the oven during long high temp cleaning and blow the thermo fuse. Just a thought.

After reading other repair reports and talking to a representative, I ordered the thermal overload safety thermostat. Relatively easy to install after removing the oven from the cabinet, only it did not work. After going over the wiring with a voltage meter, we discovered there was no power to the upper oven, only the lower oven was working. Took the panel off the top of the oven and found a wire which was not attached to anything. Never needed this part at all. This oven was purchased from a second-hand store and was used in a remodeling. $52 for part and $100 for serviceman to make the oven operational.

This site helped me diagnois the problem rating the suggested problem as a 99% chance cause of the problem. Ordered the thermal overload safety thermostat and it arrived in just two days. Repair was quick and easy once getting the oven removed from the cabinet. (It's very heavy so have some assistance or a sturdy stand to set it out on.)#2 Phillips scredriver and needle nose pliers were only tools needed. Overall, an easy repair for anyone.

INNER GLASS - A YouTube video on removing Whirlpool Oven Doors was very helpful. Cleaning the other two panels of glass with a Baking Soda paste worked like a dream. Re-assembly was fairly easy. The hardest part was re-aligning the outer glass cover's top holes so I could drive the screws in. LIGHT BULBS - To easy to describe.

Had to screw off old terminal block & screw on new one

Removed the door from the unit. Set the door face down on a work surface. Remove the screws and put them in a separate place from the rest of the screws (They are a different style of screw). Turn the door back over. Remove the two clips at the bottom on the door. The door front will slide down. Set the door front off to the side with the two clips and the screws. Remove the screws securing the brackets for the next level of glass (Mark which it the top and which is the bottom bracket. Place the glass, brackets and screws together. Remove the next glass/bracket assembly and set it aside with the screws. Lift the inside metal glass retainer and set it aside. Remove the old glass and install the new glass and reverse the order of the disassembly process.

Removed oven from the wall. Take off back panel. Removed thermal overload thermostat. Replaced with new part and works great.

Turned off the power/ unscrewed the oven from the cabinet and slid it out took the back off the oven and the part was right there. What I would like to know is why this happens so frequently? This is the 2nd time and it always happens after the self cleaning is done.

took out door hinges, slightly close door, lift upwards, remove clips on bottom of door, remove screws from 2 inner layers of glass, insert new glass, perform revers order reassembly..cleaned all inner glass, and surrounding parts prior to reassembly

find the owner's manual & follow the instructions for inserting two allen wrenches (assuming that you cannot find the "removal tools" that came with the oven) into the holes near the hinges on the door, carefully & slowly close the door with the wrenches inserted until the hinges disengage from the wall mounted oven. Lift the door away (is rather heavy). It is necessary to remove panels from the front one layer at a time to reach the 3rd layer of glass (the inner most glass that is the rather easy one to break). Be slow and methodical. Not a challenge once you study the owner's manual for door removal instructions.

I was able to convince a local mechanic that he could do this after watching it done four times. The most difficult part was unscrewing and taking out the oven to get to the back. He suggested since this has happened everytime I used the self-cleaning feature, that I cut a hole in the wall for easier access (tongue-in-cheek). The most difficult part was dealing with the extended warranty service plan - this is covered, but they could not find a technician to do this. Then I found out they don't pay mileage so who would want to come out to a rural ND ranch to repair an oven?

Door repair assembly was simple, did without any instructions or manuals. Fan assembly, the actual fan replacement was easy, it was the number of pieces of metal that needed to be removed i order to get the main rear panel off to access. Also had to remove panel from inside the oven; requires two people to loosen screws from inside while the other person holds the fan assembly from the rear side of the oven. Didn't have any instructions for this task either, figured it out anyway, just follow the layers.