MEW6627DDS Maytag Wall Oven - Instructions

Watched the video and it was as easy as described. Not many things go as easily as this.

New part delivery was prompt, arrived within 24 hours and was well-packaged. Removal of old element was complicated by one of the two original wires being caught up in the housing behind the oven. After removing the circular metal plate in the back of the oven the offending wire could be accessed and rerouted. Plugging in and installing the new bake element was quite easy and without complications.

Removed 2 screws holding the lower element (hard but they actually came out after 12 years) and pulled the wires out to expose the wire connections. I didn't turn off the breaker since the oven was off. BIG MISTAKE. One of the connectors touched the oven case and blew off the end of the element. No problem luckily. After turning off the breaker all was OK and easy. Connected the wires to the new element and put back screws. Screws are not tightening up all the way but they won't pull out with moderate pressure so I'm calling it finished. If I get energetic I might try slightly larger screws sometime. Took less time than writing this.

This was a really easy fix... All I needed to do was remove the door and racks from the oven, remove 3 screws from the fan cover and another 4 screws from the fan itself, disconnect the two wires (keep track which side each was on) remove fan from oven. I then took the new fan, connected the wires installed the screws and door and Done! Now for the moment of truth the test... Works Great!! Easily cut my repair bill in half by doing it my self... no repairman costs, not travel charge, and no markup on the part:)

Very simple, hooked up with two screws...so easy, and ordering was so easy and came in two days!,,

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

Followed provided video

Easy peasy.....Turn off the power in the breaker box to the oven. Take the racks out of the oven,remove the two screws in the very back and pull the element out a few inches(don't be afraid, you may have to use a little force). Pull the clips off of the element and remove it. Replace with the new element and reverse the proceedure. I love knowing I found a websight that had what i needed, was easy to navigate, and offered instructions with the part. NICE!

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

sorry, son did job. It went like a charm. Easy, quick, and works great.Thanks

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair