CWG3600AAS Maytag Wall Oven - Instructions

Removed oven bottom were you see the light glowing from then unscrewed igniter unpluged then took it out and put in new one went well i would do it again works great

I simply pulled the stove away from the wall, disconnected the gas and electricity. Then took the pan out from stove. At which time I used a socket to remove the two srews and then unplugged the part from the back of the stove. After that, reattached the screws, plugged it in, reconnected the gas and electricity, and pushed the stove back against the wall. Fired up the oven and it has worked like a champ ever since!

First I unplugged the range, turned off the gas to the oven and disconnected the gas line from the oven. I pulled the oven out to gain access to the rear of the unit and unplugged the old igniter. Next, I removed the oven door, removed two screws to the floor of the oven and removed it. I then removed the metal covering above the gas component allowing full access to the igniter. I removed two screws from the igniter and removed it. I positioned the new igniter and replaced the two screws. I replaced the covering over the gas component, replaced the oven floor and put the oven door back on. I went to the rear of the unit and plugged in the new igniter. I then reconnected the gas line to the oven range and checked for leaks, No leaks were found and I pushed the oven unit back into place. I pushed the Bake button and the igniter started igniting the oven.

Job completed.

1. Turn off the gas (propane)
2. Unplug the oven.
3. disconnect the gas line and pull the oven out.
4. remove the back panel to access the igniter.
5 disconnect the igniter.
6. unscrew igniter/gas assembly and remove from oven (two screws).
7. unscrew igniter (two screws)
8. replace igniter with new.
9. reassemble in reverse order.
10. turn on stove.
11. Happy wife, happy life.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

It took all of 10 mins. Open oven door slightly lift to remove.took out shelves and bottom of oven,lift at back to remove.Two screws hold the Igniter, was able to pull the connector into the oven to change. Oven works great!

First i removed the two screws that hold the element in place. I then pulled the wire out of the hole and disconected the plug. then plug in the new one, put the two screws back in, and checked it to see if it worked,It worked like a new one! So as my reward my wife baked me cookies!

This is simple for most people - unscrew and remove the bottom oven floor pan. There is the igniter, removed with two screws with a 1/4 nutdriver. However, my problem was that when I unclipped the old igniter, I dropped the over part of the connection, it fell down the hole, through the insulation, to the bottom of the stove where the wiring is. I had to pull out the stove to get to the connection, push it back up the hole to the oven, then install the igniter. My advice: do no lose your grip on the oven wire whatever you do. Otherwise, it was a snap, even for a klutz.

Bought the igniter, replaced it with the old one and it works great.

Unplugged the oven from electricity. Took off the bottom(Floor) of the inside of the oven. Checked that the new part looked the same as the old. It did. Then I checked the back of the oven, had to take off a cover, and the connector in the back was not the same. I did not that it had the same two wires so rather than send it back, I figured I could make it work. I started to take off the old piece by unscrewing the two screws. They were a bit rusted, one came off the other I had to hacksaw and twist off. I cut the old connecting end off of the old part and the end off of the new part stripped the cover off the ends of the wires, and put the old end to the new part, having also put the old wire covers over the new wires. then twisted the end together and wrapped the in electrical tape. I had to take the piece that held the new part out of the oven the tried to use the one semi-good old screw, then some newer screws, then finally used some new nuts and bolts to connect the part tightly. put everything back together and it worked.

i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace

Removing the oven door by partly opening it and pulling it up out of the hinge made access to the igniter much easier. Access to the igniter was easy. Just remove the baking shelves and lift out the bottom panel. I removed the two screws holding the old igniter. One screw was difficult to remove because of oxidation, and required some tinkering as the threads were stripped. But once the screws were removed, the igniter was easy to replace and connect to the gas controller with a simple plugin connection.

Suspected the igniter, and verified by reading comments on your parts site. The mounting screws were frozen so I used larger screws. Piece of cake! Wa La!

The igniters burn out periodically, light bulbs, and have to be replaced. There are two of them, one for the oven and one for the broiler. To get access to the one for the oven, I removed the shelves and the floor of the oven. It lifts out. Two screws hold the igniter to a mounting bracket by the burner. The wires on the igniter pass through a hole in the back of the oven. There was not be enough slack in the wire to get the connector through the hole, so I had to get acess to it from below. I removed the storage drawer from the range. At the back, behind the drawer is a panel that's held on by two screws. I removed the panel and disconnected the igniter wires. I fed the new igniter wire through the hole in the oven and connected it. Then I replaced the panel and the drawer, screwed the igniter in place and replaced the floor of the oven.

It is the first time that such a repair has to been done on my appliances.
The serviceman did a marvalous job after receiving the parts.
Within an hour the range was working a new.
Many thanks for the prompt service.