CWE5800ACE28 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Scotch Plains, NJ
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Burned out element
Very easy since it was an exact match to the old burned out element.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Coreen from Hagerstown, MD
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower oven heating element burnt out.
I shopped around locally before shopping online. Parts Select provided me with significant time and money savings.
Turn off power. Remove the element. Installed the new element. Turned on the power. Easy... Easy... Easy...
Turn off power. Remove the element. Installed the new element. Turned on the power. Easy... Easy... Easy...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dwayne from Atlanta, GA
- Parts Used:
- WP7112P004-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Brea, CA
- Parts Used:
- WP7406P203-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler element burned out
Removed 2 element support screws and 2 element electrical connection screws. Removed the old defective element and replaced it with the new element reusing the four screws.
I received the new element two days after ordering in. Excellent service!
I received the new element two days after ordering in. Excellent service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert W from Seattle, WA
- Parts Used:
- WPW10201915
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven lights fsiled and the paer suoolied workes ierfectly
No problems withe the correct part. saved $200 ib servicw cajjs plus $49 on the part....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Derek from Marietta, GA
- Parts Used:
- 74001984
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Wrench set
Springs on both hinges for upper over (double-over) needed replacing. Oven door slammed down and could have hurt someone.
Couldn't get oven to slide all the way out of cabinet. Disconnected electrical (first threw correct circuit breaker), then slid oven out. Removed applicable parts to get to the hinges. Later realized the oven WOULD slide all the way out of cabinet WITHOUT disconnecting electrical. Once oven was slide out far enough from cabinet, oven door hinges were easily accessable and it each hinge only had two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Macon, GA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom heating element burned out/ broke.
First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERALD from HUNTINGTON BEACH, CA
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door seal badly deteriorated
The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from New Roads, LA
- Parts Used:
- WPW10201915
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Control Module Failed, oven would not work
I found the oven model #, and ordered a control module from Part Select. Rcvd the part a few days later, carefully installed and wired it in place like the old one. Well, to my surprise, it did not work. So, I called Part Select, ordered another and I will return the defective part for credit. The second module was rcvd, installed and works just fine. The two reps I spoke from Part Select were very professional and helpful. I am hoping I will receive credit for the defective part as they said they would. Al
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Mill Valley, CA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element Replacement
Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.
Was this instruction helpful to you?
Thank you for voting!