CWE5800ACS14 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Brea, CA
- Parts Used:
- WP7406P203-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broiler element burned out
Removed 2 element support screws and 2 element electrical connection screws. Removed the old defective element and replaced it with the new element reusing the four screws.
I received the new element two days after ordering in. Excellent service!
I received the new element two days after ordering in. Excellent service!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from San Jose, AL
- Parts Used:
- WP7406P203-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace the burnt out Broil Element (Top)
The part arrived promptly and as described. I had already unscrewed the bad coil so it was easy to just put the new one back in on the open sockets. I then put the top support plate through the element and quickly screwed it back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Camp Springs, MD
- Parts Used:
- 7201P003-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Had to replace heating element and element gasket
Removed old element and element gasket. Replaced both by alining gasket with element and screwing in retaining screws. Jod completed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert W from Seattle, WA
- Parts Used:
- WPW10201915
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven lights fsiled and the paer suoolied workes ierfectly
No problems withe the correct part. saved $200 ib servicw cajjs plus $49 on the part....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERALD from HUNTINGTON BEACH, CA
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door seal badly deteriorated
The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Al from New Roads, LA
- Parts Used:
- WPW10201915
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Control Module Failed, oven would not work
I found the oven model #, and ordered a control module from Part Select. Rcvd the part a few days later, carefully installed and wired it in place like the old one. Well, to my surprise, it did not work. So, I called Part Select, ordered another and I will return the defective part for credit. The second module was rcvd, installed and works just fine. The two reps I spoke from Part Select were very professional and helpful. I am hoping I will receive credit for the defective part as they said they would. Al
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Mill Valley, CA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element Replacement
Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- martin from portland, OR
- Parts Used:
- WP74011278
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
oven light replacement
bought used, oven light was damaged from previous repair attempt, without installation instructions removing the fixture was tricky, had to bend the housing tabs inward w/screwdriver to release fixture (more damage). once out the new fixture went in place quite easily, wires simply hook up, re install back panel, re-connect power, Have a nice Day!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Locust Grove, VA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Coil burned out
1. Turned off oven electric power at circuit breaker.. 2. Removed 2 screws at coil at back of oven. 3. Pulled coil away from back of oven. 4.Pulled power wire clip up vertically from coil.One clip was too tight to pull up by hand. Used a pair of pliers. 5 Removed coil and put new coil in place with wireclips. and screws provided.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from North Canton, OH
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Very Easy
Changed bake element in oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Macon, GA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom heating element burned out/ broke.
First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from Azle, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven was not heating on bake setting
I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.
Was this instruction helpful to you?
Thank you for voting!