CWG3100AAS13 Maytag Wall Oven - Instructions

igniter would heat but oven wouldnt come on or would intermittently.opened door a little and lifted it off removed racks and bottom shield removed wingnut and burner shield,removed 2 screws holding igniter ,took off lower shield to allow access to plug,unplugged old one plugged in new one replaced shield and 2 screws holding igniter,put oven back together in reverse order,works like new :) ps if unit not unplugged from wall be careful igniter is hot with electricity and will bite you OUCH!

Removed the drawer and the flash plate underneath .
Unplugged the igniter then opened the & removed the over door . Lifted the bottom plate to expose the burner and igniter . Undo the 2 screws holding the igniter in place . Replace the igniter and reach underneath and plug the wire connecters together . Place all the proper things in their place .. and it was finished ...
The biggest snag I ran into was the one of the 2 screws stripped out when when taken things apart .. but I have taps and found a few new screws and replaced them ......
Quite easy fix .. don't a pay repair man to do it .... !!

I first matched the symptom (very long preheat time/gas odor) with the most likely problem (faulty oven gas igniter). I then wrote the model # and Googled gas oven repair and got to your website. I then located the faulty part within about 5 clicks and proceeded to order the exact part within another 5 or so clicks. I received my order from PartSelest in 2 days and had the oven working with the new igniter in about 10 minutes....Then it dawned on me---"Hey, I should be a Maytag Repair Man."
Thanks for the prompt delivery and the correct installation instructions. I will absolutely use your service again. (Not too soon, I hope !)

The heat sealing strips are elastic type material with hooks on each end. I simply removed the old strips and hooked the new ones in place.
It was easier than I ever dreamed possible!
And my kitchen is now nice and cool.
Pat Morrison
Sanger TX

I didn't. Don't know how to get to light bulb to change it for this specific model

it was actually pretty easy, it took about 20 minutes to fix, i had to unscrew the bottom portion of the oven to get to the Igniter on the bottom, then unscrew the Igniter, take off the old pice, and snap the new one in, put it all back together, and that was about it, i had dinner done by the time my husband got home from work. thanks

took out racks removed 2 screws holding igniter removed 4 screws on back of stove and unplug igniter. reversed the order installing the new one

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

The trickiest part was making sure that the correct part was ordered. The first attempt was a failure. The seal was too long and the clips were too big.
After finding the correct part it was a breeze.

Oven and broiler have two seperate igniters. Broiler worked but oven did not heat. Oven igniter located under metal pan at base of inside of oven. remove pan by lifting, and remove completely from oven. Igniter under this pan and held in place by two srews. Remove screws, unplug from cable, replug in ne igniter, replace two srcews and pan, and you're done! this part cost about $50 and I installed, last time Sear replaced =$300.

1. Remove the oven door by opening a few inches and lifting straight up. Remove racks to access it. 2. The old igniter is just held in by two nuts that have a screw head in the middle of them so they could be removed by a nut driver or by a screwdriver. Unfortunately, both of our screws threads were terribly stripped and after first trying to use pliers to help remove them, we ended up using a dremel tool to cut them off. 3. unplug the old igniter and take it out. 4. Plug in the new igniter. 5. attach the two screws. (our time on the repair was mostly spent trying to find two screws around our house that would replace the two that were stripped--otherwise this would have been 15 minutes). 6. return the door and racks by the sliding the door downwards onto the hinges

I ordered a new igniter and when it arrived, i removed the door from the oven. It just lift's off. I had to removed two screws from the bottom plate to gain access to the igniter. Remove the two screws from the igniter and unplug it from the back of the lower back of the stove. Place the new igniter where the old one was and plug it in. Put new screws in and tighten them down. Put the bottom plate back in its place with screws tightened. Put oven door back on and turn on the oven. That's all there is to it. Your done.

Took the bottom out of oven then removed and replaced with the new part. VERY EASY! I'm a 70-year-old woman and do quite a few home repairs myself.

Removed door and bottom oven pan to expose igniter. It was held in place by two sheet metal screws. Tried to back them out but due to heat damage , they stripped. I used my versa tool with a metal blade to cut the screws. I removed the old igniter and disconnected the plug, after I guided it out from the insulation. I installed the new igniter with two new self tapping screws after I connected the plug and guided it back through the insulation. Reinstalled the oven pan and door. I set the oven to 350° and the new igniter worked. Wife is happy and I saved the repairman fees.

I took the broiler pan out of the shipping container and put it in the oven.