CWG3100AAS Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Cassmer from Commerce Township, MI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
oven would not light
easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ricky from hollister, CA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not heat up over 200
unplugged range took the oven racks out removed bottom plate, removed 2 screws from the igniter, wiggled the connector out of the hole, unplugged the connector. reconnected the connector reattached the igniter and put the plate and racks back in plugged the range in and it works just like it should. took about 15 mins. easier than I expected.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Alpharetta, GA
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Gas smell and oven won't get hot, or takes too long.
I turned off the gas supply and unplugged the power source first. Then I removed the old igniter, by removing the plug wire clip from the back of the stove. I then removed the oven door by simply sliding it up and off the track. Once the oven door was removed I could easily access the igniter after removing the heat shield at the bottom of the stove. I had to remove two screws that mount the igniter. I had a little problem removing one screw, because it was stripped, so I had to use my Dremel tool to cut off the screw. Once it was removed the igniter was easily replaced with the new one. My wife and I was really excited that the fix worked! Saved me hundreds of dollars. Money I used for the holidays. Thanks Part Select!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Magnolia, TX
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven would not lite
used screwdriver to replace oven igniter , we are planning to buy a new oven in the future , now we can buy it when I can better afford it. Thank you for you help I'll be back.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gary from weston, WV
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
oven would not light and gas fumes came out before lighting
took the top oven door off because you need to reach back to take off the igniter it take a 1/4 inch socket to do this only 2 bolts or screws then slide to stove out a bit to reach the plug in the back of stove its a clip type plug in it don't matter it plugs one way cant get it wrong that it put the new on but slide the plug through the hole in the back of the oven first then bolt it back and your put the clip on in the back of the stove. turn it on. mind came on fast and that is what you want it to do your done. this repair is in the bottom in the broiler area might need a flashlight to see with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Barrington, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad igniter
Shut off power, pulled oven out, shut off gas, removed racks and bottom cover. Two bolts held the igniter on, remove those and feed the electrical connector plug through the back of the oven and replace igniter. Be sure the bolts are not too rusty as one if them sheared off and I had use a pair of side cutters to hold the screw while I removed the broken section of the screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERALD from HUNTINGTON BEACH, CA
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door seal badly deteriorated
The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Centuria, WI
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not light
Got the part, changed it, works great. That's all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Workforce Initiatives from Jeffersonville, VT
- Parts Used:
- 74007498
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
igniter went bad
opened the oven door, remove racks, remove lower drawer, unscrew protective panel on lower part, take out the bottom plate, unclip the old igniter, clip in new igniter, put everything back together and you are done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Streator, IL
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven Igniter was bad
Took off oven door. Took out oven racks. Took out bottom oven cover above igniter. Igniter is held in by 2 screws,took them out with a small socket. Went to back of stove and unhooked white plug in - (part of igniter) Thats it. About as easy as it gets. Just reversed the process putting in the new one. Took about 25 minutes. It would have taken less time but I had a problem with one of the screws. Probably from the heat. The oven is 9 years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Placitas, NM
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bottom burner would not light
Followed the instructions that were provided me when I ordered the Gas Oven Igniter
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from Morrow, OH
- Parts Used:
- 74007498
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Igniter would glow but not light the stove
I replaced the igniter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DYKO from ALDEN, NY
- Parts Used:
- 74007498
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Oven Burner Would Not Start Fifty Percent Of The Time.
My top burners and broiler were working fine so I knew it was not a gas pressure issue,after reading other peoples oven issues I felt comfortable that my problem was the oven igniter, the igniter was only building about 50 to 75 percent of the normal glow/heat needed, thereby not creating enough heat to trip the sensor that opens the oven burner gas valve. 2 Screws hold a drip pan which after removed allow access to the igniter. 2 Screws hold the igniter in. You need to access the rear of the stove to plug in the new igniter connector at a 1 screw access panel in the center of the back of stove. My oven has been working great since the repair. I would recomend partselect anytime, I ordered the wrong igniter, the diagram is confusing so be carefull , and had to send it back , I got my refund in less than a week. Good luck from beautiful western new york state.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Moshe from Brooklyn, NY
- Parts Used:
- 74007498
- Difficulty Level:
- Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
it was not the part i asked for the frame and plug didn't fit
i took out the new peace from the frame and i replaced into the old frame then i chopped the new plug also chopped off the old plug i connected the wires with electric tap then it got ready to plug in the new peace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Park Ridge, IL
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Insulation along the top of the oven cracked and broke off
Took old insulation off and replaced it with new by hooking new part in its place.
Was this instruction helpful to you?
Thank you for voting!