MEW5530ACB Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Anthony from Acworth, GA
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
My oven was not holding temperature.
I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Ipswich, MA
- Parts Used:
- 74004857
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Outer glass from oven door shattered
Removed oven door (slides out). Removed side and bottom screws from frame and slid new glass into place. screwed in the 8(or so) screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from Cape Coral, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
When We Turned On The Oven The Temp. Reading Went Up To 425 And Beeped By No Heat
Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from Bellefonte, PA
- Parts Used:
- 74003645
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
1 Pane of Inner Safety Glass
It was necessary to take the decorative glass and metal safety panel off using a screwdriver in order to get to the frame that holds the safety glass. It was hard to slide the new glass into the frame without help from a second person to hold the other pane in place.This was an easy repair to make I would just suggest having 2 people to hole things in place while replacing screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from roseville, MN
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would overheat
Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from APACHE JUNCTION, AZ
- Parts Used:
- 7403P067-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Oven light Switch
Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Hamburg, PA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced gasket around inside door
It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
Oven have F2 and F3 codes following cleaning cycle making oven inoperable
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Blanche from Woonsocket, RI
- Parts Used:
- 74003387
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light bulb socket broken
Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from Tampa, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not turn on
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Newport News, VA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn gasket
Removed old gasket and replaced with new gasket'
Was this instruction helpful to you?
Thank you for voting!