Models > CWE5500ACE > Instructions

CWE5500ACE Maytag Wall Oven - Instructions

Jump to:

All Instructions for the CWE5500ACE
61 - 75 of 109
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Ivanka from Atlantra, GA
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
3 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Aurelio from Lebanon, NJ
Parts Used:
WPY04000048
Difficulty Level:
A Bit Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers
Bad broil grill
Once oven was removed from wall not to bad
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Coreen from Hagerstown, MD
Parts Used:
WPY04000066
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Lower oven heating element burnt out.
I shopped around locally before shopping online. Parts Select provided me with significant time and money savings.

Turn off power. Remove the element. Installed the new element. Turned on the power. Easy... Easy... Easy...
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dwayne from Atlanta, GA
Parts Used:
WP7112P004-60
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
thermostat temprature bulb hanger clips
snaped them into oven cavity attached temp bulb job complete
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Scotch Plains, NJ
Parts Used:
WPY04000066
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Burned out element
Very easy since it was an exact match to the old burned out element.
1 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Janet from Ada, MI
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
2 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Schwenksville, PA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
George from Camp Springs, MD
Parts Used:
7201P003-60
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Had to replace heating element and element gasket
Removed old element and element gasket. Replaced both by alining gasket with element and screwing in retaining screws. Jod completed.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Shirley from Las Vegas, NV
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
peggy ann from forest city, NC
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
replaced oven lightbulb
very easy
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Judith from Phoenix, AZ
Parts Used:
8009
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
0 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Robert from Pasadena, TX
Parts Used:
WPY04000066
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The Bake Element Ceased To Bake.
Turn off the breaker. Remove the two screws holding the bake element and disconnect the two wires. Plug the new element in and re install the screws. Trip the breaker back on and test the oven. It works.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Denver from Denton, TX
Parts Used:
WPY04000066
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven element would not heat.
Turned power off by switching off the breaker. Removed both racks from oven. Removed two Phillips head screws at back of oven securing the old heat element. Pulled old heat element forward about four inches exposing the two power wires connected to it. Removed the wires from their connectors. Removed old element. Connected new element to power wires and pushed it back in place. Replaced new Phillips head screws. Replaced racks, and turned power back on. Oven was fixed in less than five minutes. Disposed of old element. Life is good.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Glenn from Rochester, NY
Parts Used:
WPY04000066
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
burnt out element
Very easy. remove two screwa , pull element forward, unplug.Set new element in place, plug in. push back in. Screw in both screws and your done.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jessica from Macon, GA
Parts Used:
WPY04000066
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers
Bottom heating element burned out/ broke.
First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the CWE5500ACE
61 - 75 of 109