MEW6527DDB Maytag Wall Oven - Instructions

I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

We found the youtube video created by partselect.com and followed it. We took the door apart, cleaned the inside, removed the old hinges and replaced them with the new ones. Now the door works perfectly!

Unlike many here, the oven door closed enough to come up to temperature quickly and I could not feel any heat escaping. The oven worked fine but the light stayed on because the door just wasn't snug enough. I watched the great how-to video and ordered the hinges. They arrived in two or three days! I set up a work space, cued up the video again and the new hinges were installed in just a few minutes! But the door would not close enough to turn the light off! I did some more googling around and found the magnet trick! I just happened to have the perfect size magnet from a broken souvenir magnet! and now the light stays off! I stuck the magnet (about the size of a nickel) inside the door opposite the light button. This won't help if you have serious problems with the oven door, but it works if the only problem is the light!

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.

The sensor inserts into a slot in the back side of the range. By removing screws on the heat shield on the backside of the range, the sensor wires will be exposed can be unplugged. Then remove the screws that attach the sensor to the back inside panel in the oven. Next, pull the old sensor out. The wire leads will get caught on the insulation blanket, no big deal. Reverse the process to install the new sensor. The new sensor comes with two connector sets for the wiring. I did the whole job for less than the cost of a service call.

The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.

take the old ones out and slide the new ones in ordered around 2 in the afternoon and they were delivered to my front door around the same time the next day very pleased with service and the racks. I just wish I could get parts for my Jenn-Air cooktop which is 20 years old maybe somewhere someday.

I followed the online video at Jennair.com. The repair was easy and I saved quite a bit of money. I was quoted a price of $534.00 to replace the door hinges, I did it for $96.00 including overnight shipping chargers. I am a very happy lady.

Easy peasy.....Turn off the power in the breaker box to the oven. Take the racks out of the oven,remove the two screws in the very back and pull the element out a few inches(don't be afraid, you may have to use a little force). Pull the clips off of the element and remove it. Replace with the new element and reverse the proceedure. I love knowing I found a websight that had what i needed, was easy to navigate, and offered instructions with the part. NICE!

Turned off breaker,opened door with bent coat hanger by sliding right to left the coat hanger to open the door, remover 2 screws holding in the sensor in upper left corner of the oven. Remove the sensor (gently) with the wire connection from back of oven pulling sensor out a out 8 inches . Disconnect plug. Install new sensor with matched harness /.connection, installed 2 screws ,turned on breaker.

We cut the electricity to the stove at the breaker box. We had to do that to keep the fire from spreading in the first place. We took 2 screws out and used the same screws to install the new bake element. It was just 2 connectors that had to be pulled apart gently from the old bake element. We plugged in the new bake element into the metal spaces where the old one came out. Replaced the screws and we were done. It was very easy.

Opened oven door. Inserted a small bent nail into the small holes on the hinge. This locks the hinge from closing all the way. Removed the chrome hinge retaining plates. One at each hinge. Lifted the door off the oven. Laid door on towel. Removed 3 screws from the top of door, three screws from the bottom of door. This allows you to separate the two pieces of the door. Clean all glass surfaces, including the ones under the middle glass panel. Removed 1 screw from each hinge at bottom of door. Pull hinge from bottom of door after removing screws. Insert new spring at top of door first, replace retaining screw. Realign the two door parts and replace all screws. Set door back on hinge pocket. Be careful to insure that the hinge seats into the pocket. Open door just enough to replace retaining plates. Process was easy, but it did not fix the problem completely. Bought heavy magnets from hardware store and installed them inside the door. This with the new hinge fixed the problem.

New part delivery was prompt, arrived within 24 hours and was well-packaged. Removal of old element was complicated by one of the two original wires being caught up in the housing behind the oven. After removing the circular metal plate in the back of the oven the offending wire could be accessed and rerouted. Plugging in and installing the new bake element was quite easy and without complications.