CWE550 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Bryan from Thibodaux, LA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
the element broke was old
turned off power unscrewed plate that held in element unplugged socket from old element plugged in new one screwed plate back turned on power works fine
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rebekah from Azle, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Oven was not heating on bake setting
I unscrewed the old element from the back of the oven. Then I detached the wires and took the old heating element out. I then fit the wires into the new element and screwed it back in using the new screws. It was really easy! I was lucky to have my father in law show me how, since this was my first time to do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jessica from Macon, GA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bottom heating element burned out/ broke.
First, we cut the power to the oven and removed the oven racks. I removed the two screws holding the old heating element in (removed easily, I didn't need any WD-40) and pulled the element wiring out of the back of the oven. It took me a while to realize how the wiring was/is connected to the element, but once I did they came off fairly easily with a little coaxing from some pliers. On our model, the wiring thingums fit down onto the element prongs. So, you pull the straight up to remove them. Very technical terms here. After the wires and the new element were connected, I screwed the new element in, turned the power back on and the oven was is excellent working order again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Rochester, NY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out element
Very easy. remove two screwa , pull element forward, unplug.Set new element in place, plug in. push back in. Screw in both screws and your done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Brilliant, AL
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Numbers on knobs for temperature and oven selector knobs were gone.
Just pulled to old knobs off and slipped the new ones on, so very easy to repair and now my oven looks like new. Thanks for all your help, all I needed was the model number to get the right part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherri from Topeka, KS
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element not working
Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from pantego, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
would not heat
put the old one out,put new part in that easy,works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Albuquerque, NM
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through.
Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fort Wayne, IN
- Parts Used:
- WP7711P357-60, WP7711P354-60, 71003346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
couldn't read 0ven knobs and racks needed replaced
repair was very easy. Now my wife is very happy, it was like giving her a new oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wava from Louisville, KY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke causing a flame up in oven
Loosened the two screws holding the element, pulled the element out of the back of the oven, loosed the two wire leads connected to the back of the element, removed the broken part, placed the new element into the oven, reconnected the wire leads, pushed them back into the insulation in the back of the oven, repositioned the element into its place and replaced the two screws holding it into place with the new screws that came with the new part. Oven element fired right up first try without any further complications. One of the easiest appliance fixes I have ever done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOYLE from PHOENIX, AZ
- Parts Used:
- WP7711P354-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob missing temperature settings.
My oven temperature knob has been discontinued by manufacturer Maytag. I looked thru your vast list of knobs and found one that looked excately like my knob dial. The knob is a two piece design. My shafts that the knobs slide onto are different than the one I selected but since it was a two piece knob, I was able to use the center part of my knob that fit the shaft of my oven and use the new dial face. I spayed it with a clear lacqure top coat to protect the dial face from the numbers and letters disappearing as the old on did. Worked perfectly. Happy wife, happy life. I will give your customer service an A plus as one of the dial knobs that came in a not so well protected package was bent. They agreed to send out another right away which they did. I would definately purchase from you again. Thanks so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobby from Indianola, IA
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
When cleaning the knobs all the writing washed off.
Take off the old knobs & put on the new knobs. They work & look great. Based on the age of the oven in the older home I purchased I was very concerned I would be unable to replace, but you made this very easy to do. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Independence, KY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating elements (upper and lower ovens) would not achieve the proper temp
Removed the two screws on both elements, pulled the wires off, put the wires on the new elements and put the screws back in. Very easy, works perfect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Park Ridge, IL
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Insulation along the top of the oven cracked and broke off
Took old insulation off and replaced it with new by hooking new part in its place.
Was this instruction helpful to you?
Thank you for voting!