CWE550 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rolland from New Port Richey, FL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Broiler element split after oven self-cleaning
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Berkeley, CA
- Parts Used:
- WPY04000066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bake element in lower oven had burned out
I made the mistake of thinking that, if the oven was off, there would be no voltage to the heating element. Wrong! I removed the element, wearing rubber gloves just for safety, and had no problem. But when I put the wiring back on the new element and tried to slide it into the hole at the back of the oven, one of the wires brushed the metal, sparks flew, and melted one of the wires. Even though the oven was off, this wire was hot. The solution was, of course, just to turn off the circuit breaker, reconnect the wire, and slide the element back in. It works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- OSCAR from BRISTOL, CT
- Parts Used:
- 7711P172-60
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace clock-adjust knob
Although normally a push fit, we drilled and tapped a #6-32 cross hole and used a set-screw to attach the small knob.
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
The original knob is still hiding somewhere but, thanks to PartSelect we are back in business !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from St. Charles, MO
- Parts Used:
- WPY04000066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The oven discontinued to generate any heating
The instructions reviewed in the Maytag Parts web site provided very good information that told me how to remove and replace the heating element. It took me about 15 minutes to complete the replacement. The oven then began to function properly.
I am impressed with the rate I was sent the replacement. I received the replacement within 24 hours after I submitted the request for the product.
I am impressed with the rate I was sent the replacement. I received the replacement within 24 hours after I submitted the request for the product.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- bernice from santa barbara, CA
- Parts Used:
- WP7711P357-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the white names on my selector knob had worn off.
I just pulled off the old knob and pushed on the new knob. My JENN-AIR Oven is 20 years old. The new knob is a different style and it doesn't fit snug against the oven. But it works and I can set the oven to Bake or Broil or clean and know I'm in the right place. I really like this oven and hope it will last another 20 years.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Glen Mills, PA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element disintegrated
Unscrewed old element from back of oven, disconnected and reinserted new element and screwed back into place. Voila! So glad to have saved the cost of a repairman. Where I live this would have been a $200 repair(part and service call) easily. This repair took no time at all. Very please as to how fast Parts service got the part to me. I use my oven a lot, so I was lost without it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phillip from Reston, VA
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Replaced Broiler Element
Turned off oven power.Removed oven heat shield, element support clips and element mounting plate screws. Disconnected three element power wires and ground wire. Removed old element. Reversed removal procedure for new element install. Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Flemington, NJ
- Parts Used:
- 7201P015-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
lamp retainer gasket disintegrated when changed burned out bulb
I just removed the lamp retainer plate and glass cover, inserted the new gasket, and screwed everything back in place. Simple as that. I was enormously pleased that the part arrived so quickly -- just in time for me to cook my Thanksgiving turkey and use the self-cleaning feature.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Veronika from Pottstown, PA
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
White Markings on Themostat & Selector Knob Wore Off
I ordered the new knobs, which arrived in a couple of days, pulled off the old ones and put on the new ones. Total time: less than one minute. I am very satisfied with the fast turn around time of this order. I would recommond this company.
V. White
Pottstown, PA
V. White
Pottstown, PA
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Benton, LA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Burnt out lower element
I TURNED THE POWER OFF !!! removed the two screws holding the element in place, disconnected the two power wires, installed the new element. Done, in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Raven, VA
- Parts Used:
- WPY04000066, WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bottom element burned out, replaced both elements due to age of elements
Turned off the breaker first. Remove the mounting screws and unplug the element. Then replace the new element. Then put in the mounting screws and turn the breaker on. Easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudia from hewitt, TX
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I cleaned the knobs and the numbers came off leaving me in a state of panic as I had no idea that would happen and could not even estimate the temperature.
Just took them out of the package removed the old ones and attached the new ones. I cut out a picture of the knob when the accident occurred, who would guess cleaning the knobs would erase the numbers, and taped the picture above the knob until the new ones arrived. thank you for keeping the old knobs in stock,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kathy from SANDYSTON, NJ
- Parts Used:
- WPY04000066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Blown element
Very easy. Didn't have to replace whole unit
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gerald from springboro, OH
- Parts Used:
- WP7711P354-60, 7201P015-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Replace Oven Light
When replacing the bulb the gasket on the cover was destroyed . Replaced the gasket and screwed back on. Pulled knob off and replaced with the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alex from huntington, NY
- Parts Used:
- WPY04000048
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
replace element
remove two bracket screws, and remove bracket, the remove two mount screws for element. then remove the element. installed the element in reverse order that it was removed.
Was this instruction helpful to you?
Thank you for voting!