CWE502 Maytag Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kay from Gatesville, TX
- Parts Used:
- W11238392
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
old knob broken off inside
Repair not going well. Can't get the old part out. Have used needle nose plier and still can't get ahold of whats left of the part to pull out. Not for sure what to do next.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marvin from Mill Valley, CA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Element Replacement
Turned off the circuit breaker. Removed the oven door from hinges. unscrewed the old element connection plate. Pulled off two wire leads. Reversed forward steps to completion.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GERALD from HUNTINGTON BEACH, CA
- Parts Used:
- WP7212P006-60
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door seal badly deteriorated
The seal is suspended by metal clips at each end, which are inserted into holes in the oven box. The clips on the new seal were a bit too wide to fit into the holes. so I drilled the holes larger, and it worked fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wallace from Lowell,, AR
- Parts Used:
- WPY04000048
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broil element burned out
Removed the oven door, removed old burned element, installed new element. Turned CB back on and tested oven. Reinstalled oven door. Straight forward and easy to follow directions with new element.Local appliance part house said the element was no longer available. Thanks to you I did not need a new oven. Very easy replacement job with normal tools.Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ann from Schertz, TX
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The broiler element made a loud noise.I immediately turned the overn off. It kinda acared me.
My son-in-law installed the new element. First turn off the electricity and remove oven door. Then unscrew all connections to the element.The back electrical wires come out from the top back oven. The bracket screw faces the oven and the electrical wires are so short there is very little room for a screw driver (get the shortest one you can find..abt as big as your thumb if possible).Once that was out the element came out with no problems.Then it's just reversing the step. Again, that back electical bracket is difficult to get to for install. Also, the new screws in our kit were Philips, but the old ones were flat so check those out before turning off the oven light.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Pasadena, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The Bake Element Ceased To Bake.
Turn off the breaker. Remove the two screws holding the bake element and disconnect the two wires. Plug the new element in and re install the screws. Trip the breaker back on and test the oven. It works.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Denver from Denton, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven element would not heat.
Turned power off by switching off the breaker. Removed both racks from oven. Removed two Phillips head screws at back of oven securing the old heat element. Pulled old heat element forward about four inches exposing the two power wires connected to it. Removed the wires from their connectors. Removed old element. Connected new element to power wires and pushed it back in place. Replaced new Phillips head screws. Replaced racks, and turned power back on. Oven was fixed in less than five minutes. Disposed of old element. Life is good.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from pantego, TX
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
would not heat
put the old one out,put new part in that easy,works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from Albuquerque, NM
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
bake element burned through.
Very simple. Removed two screws-pulled element out about 3-4 inches-pulled off the contacts-reversed procedure using the provided screws, turned the breaker switch on and everything worked fine. Excellent service from parts select and quick shipping.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from Brilliant, AL
- Parts Used:
- WP7711P357-60, WP7711P354-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Numbers on knobs for temperature and oven selector knobs were gone.
Just pulled to old knobs off and slipped the new ones on, so very easy to repair and now my oven looks like new. Thanks for all your help, all I needed was the model number to get the right part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- sherri from Topeka, KS
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element not working
Unscrewed two screws, unplugged two small plugs, plugged the new ones in and screwed the screws back in. Less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wava from Louisville, KY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Heating element broke causing a flame up in oven
Loosened the two screws holding the element, pulled the element out of the back of the oven, loosed the two wire leads connected to the back of the element, removed the broken part, placed the new element into the oven, reconnected the wire leads, pushed them back into the insulation in the back of the oven, repositioned the element into its place and replaced the two screws holding it into place with the new screws that came with the new part. Oven element fired right up first try without any further complications. One of the easiest appliance fixes I have ever done!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DOYLE from PHOENIX, AZ
- Parts Used:
- WP7711P354-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Knob missing temperature settings.
My oven temperature knob has been discontinued by manufacturer Maytag. I looked thru your vast list of knobs and found one that looked excately like my knob dial. The knob is a two piece design. My shafts that the knobs slide onto are different than the one I selected but since it was a two piece knob, I was able to use the center part of my knob that fit the shaft of my oven and use the new dial face. I spayed it with a clear lacqure top coat to protect the dial face from the numbers and letters disappearing as the old on did. Worked perfectly. Happy wife, happy life. I will give your customer service an A plus as one of the dial knobs that came in a not so well protected package was bent. They agreed to send out another right away which they did. I would definately purchase from you again. Thanks so much
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from North Hills, CA
- Parts Used:
- WP7212P003-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door gasket broken
This part showed up so fast I couldn't believe it. Took longer to unwrap the package than to install the gasket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Glenn from Rochester, NY
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
burnt out element
Very easy. remove two screwa , pull element forward, unplug.Set new element in place, plug in. push back in. Screw in both screws and your done.
Was this instruction helpful to you?
Thank you for voting!