CWE9000BCB Maytag Wall Oven - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Turned off power at breaker box. Removed two screws from the old bake element on rear of oven wall. Pulled out bake element from back of oven so wires were exposed (about 3-4 inches). By hand, removed the wire connector from each side of the element (wiggle it loose).

The part I purchased was exactly as described on the PartSelect website (i.e., it had the correct connections - female - on the bake element). The part arrived in 2 days in perfect condition. I definitely will use PartSelect again.

This was a very easy repair and the website helped greatly. my husband simply pulled old element out and pluged the new one in. Excellent website, saved us a lot of money.

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. That is when I notice that the new element had a female connector and so did my wires comeing out of the stove. I took the old elements male end off (with a grinder). The mail end was long enough to use it connect both female end.

Disconnected power pulled oven from wall, removed 8 screws from back, unplugged sensor, removed old, attached new, put screws back wow saved me $500. From buying new and $150. For service call

Watching the video of how to replace the sensor was great help and much appreciated, the only difference was that my wires were much shorter and I had to pull the oven out of the cabinet to get to the back of the oven to release the clip holding the wires together, unlike the video where the man jiggled the wires until the clip holding the wires together came through the little slot where the probe is attached, otherwise it was pretty simple, just a few extra steps to pull the oven forward to get to the rear to release the clip holding the wires together. Once I was able to release the clip I used one of the 2 adapters that was sent with the sensor probe and attached them after putting the wires through the hole where the probe was attached first then replaced the 2 screws that holds the sensor in place, slid the oven back in and turned the circuit breaker back on and it works perfectly. The video gave me the confidence to do this job though and I thank PartSelect very much for being a great company to help with videos and sending the parts so quickly.

I watched the video, which was very helpful...the temperature sensor was hard to pull through the small opening in the upper back left oven corner. On the back wall of the oven was a large removable circle, so I unscrewed that piece and was able to gain access to the wires attached to the temperature sensor and push it through the small opening. I used one of the new connectors, pushed it back through the small opening, screwed it back onto the oven wall, replaced the circle opening and tried the oven again...unfortunately, there was no improvement in oven temperature! My JennAir wall oven is about 17 years old, and I thought I would try this $30 repair prior to purchasing a new wall oven, but it looks like I will have to do some overtime and buy a new oven. Any other suggestions would be welcome.

I ordered the temperature sensor after watching the video and seeing how easily it could be changed out. Unfortunately, they don't tell you that it may be necessary to access the part from the back. When I tried removing the sensor from inside the oven the connection separated before getting to the hole. I tried for 4 days to try to fish out the other end. Finally, I had my brother help me remove the oven from the wall and take the back off at which time we were able to connect the new sensory. It turns out that the wiring is on the upper right hand corner of the oven and the sensor is on the upper left hand corner and the wiring is rather short. I am a 64 year old female and do the majority of repairs around the house myself, but due to the weight of removing the oven I enlisted the help of my brother. After removing from the wall the rest was a breeze. Just wish the videos or written info on the website was a little more clear as to the different ways of accessing the damaged part.

There are five Phillips head screws to remove from the door (2 top, 3 bottom); the only touch part is that there are no screws on the sides, but instead plastic tabs on each side that "latch" inside the door frame; you have to use a flat blade screwdriver to work each tab and press on the door frame to unlatch each tab (yup I broke one, not knowing the setup the first time, but it went back together OK anyway). Once the tabs are unlatched from the frame, the entire front or the door will come off (be ready for this); then, just a few screws to take off the 2nd inner door glass frame (remove second glass carefully), and your to the inner glass, which just fits within the frame. Then, carefully backwards and the door is together again (once again, provide support as you take the last tab/screw off the outside of the front door, or you'll have more broken parts).

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.

I replaced the oven sensor which was easy to replace. A pigtail wire was provided with the sensor which is intended to be installed first so you don't have to reach around the front and back of the oven at the same time. The replacement was easy. However, that turned out not to be the problem. The real problem was the maytag electronic clock control timer, temperature control unit. The part number is 7601P177-60. This device has been discontinued and I was fortunate enough to find the part at a local supplier. Once I replaced this, the problem went away. The oven heats up normally. My original symptom was that when setting the oven temperature to something like 350 degrees, the display would rapidly report heating up the oven to that temperature, and the oven was only mildly warm. If you have that symptom, it is probably not the oven sensor. It is the electronic clock unit. Hope you can find one. If you can't, I think you need to by a new oven. Regards

Replace the oven sensor per the excelent easy video you provided

I removed the old sensor via the two screws holding it in, unplugged it and replaced it with a new one.