9512WUV Magic Chef Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Stephanie from MOUNT JOY, PA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element cracked
Easily disconnected the wires and removed cracked element and replaced with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Pittsburgh, PA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower heating element not working
I removed the two screws that held in the old part. I pulled the element out a few inches.I disconnected two wires from the old element and connected it to the new. Using the screws provided I reconnected the unit. All went well. No need for repairman. 1
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Samuel from San Fransansico, CA
- Parts Used:
- WPY04000066
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The plate is diffrent shape and holes was diffent .
I drilled two holes on the plate and I did use same original screws.
I just wanted to say once it was installed, It worked great.
Thank you,
Sam
I just wanted to say once it was installed, It worked great.
Thank you,
Sam
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from San Rafael, CA
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Replacement of broil element in wall oven
In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw driver is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherrie from Elverson, PA
- Parts Used:
- WPW10273818, 71003346
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The old racks were beyond cleaning
I installed the new racks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from METAIRIE, LA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Bake element was burnt out
Shut off electricity to oven. Remove existing screws attaching element to back wall of oven. Use pliers to pull off wire connectors. To install the new element, reverse these steps. It's that simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from SOUTHFIELD, MI
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Lower bake element would not heat.
Removed two screws. Gently pulled old element away from back of oven, exposing two wires. Disconnected the element from wires by pulling the ends apart with hands. Reconnected the wires with new element. LESS THAN FIVE MINUTES! Saved about a hundred bucks!. (Demo on You Tube.)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- harry from front royal, VA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
240 Volt Bottom Elment Burned Out
Turned breaker off to oven, removed two screws disconnected two wires. Reversed order to install. Piece of cake. Stuart,in va.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lebanon, NH
- Parts Used:
- WP7212P003-60
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed to replace a side oven door seal
The trickiest part was making sure that the correct part was ordered. The first attempt was a failure. The seal was too long and the clips were too big.
After finding the correct part it was a breeze.
After finding the correct part it was a breeze.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- maria from MANTECA, CA
- Parts Used:
- 7731P038-60
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Inside was missing
Great I can bake now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary L. from SUN CITY, AZ
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The oven heating element burned out and would no longer heat.
It was very simple. First thing I did was to go online to youtube and type in the kind of repair I intended to do. There were several short videos showing you how to do the replacement.It was easy and took about 30 to 45 minutes. First thing is shut off the power to the oven. ( Very important). You then need to take out two screws that hold the element in place. At this point, just pull the element toward the front of the oven. You will see some insulation at the hole where the wires come out. Slowly work the element forward until you see the fasteners on the wires ( two wires).Disconnect the fasteners and throw the old element out and put the new one in the oven.Connect the element, push everything back into the hole and screw the element to the back wall. You're done ! I had two wall ovens to fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rolland from New Port Richey, FL
- Parts Used:
- WPY04000048
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The Broiler element split after oven self-cleaning
We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Yafa (and David) from Bothell, WA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Manuk from STUDIO CITY, CA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Bake Element Burned
Turn off the electricity for the oven from the switch box. Unsure the damaged element from the unit. Pull it forward and unplug connections. Then plug the new element and use the new screws to screw it back to the unit. That's all
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christina from Glen Mills, PA
- Parts Used:
- WPY04000066
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
heating element disintegrated
Unscrewed old element from back of oven, disconnected and reinserted new element and screwed back into place. Voila! So glad to have saved the cost of a repairman. Where I live this would have been a $200 repair(part and service call) easily. This repair took no time at all. Very please as to how fast Parts service got the part to me. I use my oven a lot, so I was lost without it.
Was this instruction helpful to you?
Thank you for voting!