9824XPB Magic Chef Wall Oven - Instructions

This was too simple, turned off the power to the oven, undid the two screws, unplugged two wires, plugged wires into the new element, fastened the new screws and turned the power back on. Turned on the oven, what do you know, it works again!

The element did not come with instructions and none were needed.

Removed two screws. Gently pulled old element away from back of oven, exposing two wires. Disconnected the element from wires by pulling the ends apart with hands. Reconnected the wires with new element. LESS THAN FIVE MINUTES! Saved about a hundred bucks!. (Demo on You Tube.)

It was very simple. First thing I did was to go online to youtube and type in the kind of repair I intended to do. There were several short videos showing you how to do the replacement.It was easy and took about 30 to 45 minutes. First thing is shut off the power to the oven. ( Very important). You then need to take out two screws that hold the element in place. At this point, just pull the element toward the front of the oven. You will see some insulation at the hole where the wires come out. Slowly work the element forward until you see the fasteners on the wires ( two wires).Disconnect the fasteners and throw the old element out and put the new one in the oven.Connect the element, push everything back into the hole and screw the element to the back wall. You're done ! I had two wall ovens to fix.

Very easy. Didn't have to replace whole unit

Awesome, just awesome, you guys are great and I will use you again and again.

This was an easy thing to do. Take the two screws off the back, pull the wires out, pull off the connectors, get the new element, replace the connectors, make a hole in the insulation, fish the wires back behind the insulation, screw the mounting screws and turn it on. The only thing I did extra is clean the bottom of the oven because with the element out, it's easy to do.

Determining the correct bake element to order was the most difficult part. Once I received the part, it took me 2 minutes to unscrew the back panel, detach the wires, connect the new wires and re-connect the back pannel - turned the oven on to test - and we were all set just in time for Chistmas baking.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.
Went online and Googled for oven element by providing the serial and model number. Partselect popped up. I submitted the order and received and installed the new element within 5 days from start to finish. I recommend this website for replacement parts.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, that were clipped on. slipped them off connected the new element screwed it back into the oven.

Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

unscrew the old ones and replaced the new one - easy as that! Savings of over $300.00 if I need to buy a new one! Thanks for the speedy service after I ordered it.

Simply removed old element,2 screws,clean'd oven b/4 install'n new one,reconnect'd 2 wires,2 screws & yea oven wrks again. My husband was very happy as the oven is 34 yrs old,I just copied the model #,went 2 u'r web site,& we r very happy campers,so thank you very much.
Debbie A. Martin

First, I want to say that this part arrived within 24 hours of placing the order. I was plesantly suprised. My husband did the repair and it was super easy. We had no problems.

Thanks PartSelect!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Connected the wires to new element, pushed wires back into the back wall, re-installed screws.

Pulled the old one out and installed the new one