9895XRB Magic Chef Wall Oven - Instructions

First of all called my local appliance stores and was told that no one had parts because the range was too old. My husband was adamant that we needed a new stove. After much searching found a part on your site. The repair was soo easy a mere woman can do it. Required a screw driver and patiently taking the door apart. Could have been done faster if I had not cleaned everything back to new condition. Easy repair. . . Awesome service from your company!

Took four screws out, pulled old one out and disconnected two wires and waited for new part to be delivered. installed part in one minute. I had the same thing happen 5 years ago and the repair person charged me $150. This time it cost me $40 .

I followed the instructions that were posted on the web site for the replacement of the element. I found everything exactly as described in the procedure. I disconnected the two screws that held the old element, removed the old element, inserted the new element and replaced the screws. I turned the oven control on and the element heated up. Everything has been working just fine.

very easy

Screwed in light bulb and glass protector

Husband got on partselect.com and read reviews, we ordered a long oven sensor kit. When it came in the mail, I took it out and look at it, decided I could probably switch the part.... and so I did. Easy Breezy ... and it worked well

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

First I remove th screw that held the element in place then I pulled the element out and disconnect the wires. Then I replace the new element, I connected the wires back then I put the screws to hold the element.

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

I slide the oven out from the counter and unpluged it. I removed all the oven racks. I then removed the machine screws that held the sheet metal that covered the back of the unit. This made it a lot easier to disconnect the long oven sensor wire and put the wire through the insulation. I removed the two screws on the inside of the oven that held the sensor onto the inside rear wall of the oven. The old sensor did not test too bad but the temperature is reaching the set temperature. I still had to adjust the oven temp up ten degrees using the control panel. I have learned that it takes a few cycles of the element going off and on during the warming to reach the desired set temperature. One more issue is that the buzzer goes off signaling that the set temperature has been reached when it has not. When I set it for 350 F the buzzerr goes off at 280 F and I have a good oven thermometer. I own three oven thermometers and they all read the same. We use to have nothing but Maytag appliances but no more. We have had issues with Maytag front loading washers and ranges. PartSelect is great. Good prices and fast delivery.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. That is when I notice that the new element had a female connector and so did my wires comeing out of the stove. I took the old elements male end off (with a grinder). The mail end was long enough to use it connect both female end.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

This was a very easy repair and the website helped greatly. my husband simply pulled old element out and pluged the new one in. Excellent website, saved us a lot of money.