CGW3330ADB Magic Chef Wall Oven - Instructions

easily pulled old seal out and push new seal in place simple and quick.

took oven tray out and loosened igniter and replace same works great.

Remove two screws back panel and remove sensor two screws inside top oven.

Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

Once I saw the spring clips on the new door seal, it was easy to understadn how to remove the old seal and install the new one. Looks nice !

it was so easy my wife could do it!!!!!!!!

1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

I found the panel on the innernet, ordered it and when it arrived I removed the old one and replaced it with the new one.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.

After unplugging the oven from the wall, I removed the grates and floor of the oven, and the thing that spreads the flame out. Needless to say, I'm no repairman! Next I simply unplugged and unscrewed the old element and screwed and plugged the new one in. Replaced the floor, grates, and flame thing in, and we were back in business! It was a very easy fix, and Partselect.com was a pleasure to research and do business with! I would certainly recommend this site to others.

Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!

During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.

My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!