CEW3330AAW Magic Chef Wall Oven - Instructions

Removed two screws, unplugged the old unit, plugged in the new, screwed the new in. Job done. Would have been less than five minutes if I hadn't kept dropping the screws.

Our oven quit working again. I called the repair(dealer) man and he said we needed a new control panel. It would cost $180.00 and labor would be $60. The total repair would be $240.00. We considered just purchasing a new one. It is a slide-in range and they start at about $1500. So I began looking for a control panel on line. I found your web site and entered what was wrong with the oven. Your site suggested we try replacing the oven sensor. There was a video that showed how simple the repair was. We ordered the part. It came quickly and I immediately made the repair (about 10 min). I was very disappointed that it did not work. I went back to you web site and tried the next option. It was a terminal block for only $20.00. I didn't even know what a terminal block was, what it looked like or where on the range to find it. But I went again to your video and I learned quickly what to do. I ordered the part and it came in two days. I made the repair in about 15 min. My wife was very happy that the repair worked. Our total cost was about $80. The $240 quote would not have fixed the oven anyway. The repairman was wrong. I was very happy with the results and the money we saved.. Good Job PartSelect and thanks.

Removed frame to cabinet lag screws
Slid oven out of cabinet (required because wire harness could not be pulled through inside of oven)
Removed two screws holding attaching sensor inside oven
Uncoupled wire harness
Installed new sensor in reverse order

Unfortunately, neither the new bake element or sensor fixed the problem, so I just ordered the more expensive control board -- hope that does it.

First of all called my local appliance stores and was told that no one had parts because the range was too old. My husband was adamant that we needed a new stove. After much searching found a part on your site. The repair was soo easy a mere woman can do it. Required a screw driver and patiently taking the door apart. Could have been done faster if I had not cleaned everything back to new condition. Easy repair. . . Awesome service from your company!

Control panel was responsive however oven would not heat up. I Replaced sensor with one of the adapters and oven is now working again.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Installed new thermostat. Went well. Now the oven comes on and it takes 2.5 hours to come up to 250 degrees. Help!

Followed directions as supplied. New part did not work, so it must be in the control unit which is no longer available. So time for a new range.

There are five Phillips head screws to remove from the door (2 top, 3 bottom); the only touch part is that there are no screws on the sides, but instead plastic tabs on each side that "latch" inside the door frame; you have to use a flat blade screwdriver to work each tab and press on the door frame to unlatch each tab (yup I broke one, not knowing the setup the first time, but it went back together OK anyway). Once the tabs are unlatched from the frame, the entire front or the door will come off (be ready for this); then, just a few screws to take off the 2nd inner door glass frame (remove second glass carefully), and your to the inner glass, which just fits within the frame. Then, carefully backwards and the door is together again (once again, provide support as you take the last tab/screw off the outside of the front door, or you'll have more broken parts).

removed 2 screws in probe and pulled it out.had to take back off as wire was tangled from factory and couldn't do quick repair

I removed the broken hinge and installed the new one, however the oven door didn't stay ajar but dropped open fast. So I took the old spring and installed it on the new hinge and it was improved. It just took a screwdriver.

Removed glass and then two screws to remove metal plate pulled out socket,disconnected two wires and installed new socket.

It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.

Followed provided video

Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!