9121WPW Magic Chef Wall Oven - Instructions

placed knob on clock shaft with my fingers

I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.

First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the electrical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.

Fist I removed the screws on the front-sides of the oven. Then I turned off the gas, by adjusting the in-line valve. I then unscrewed the gas fitting going into the bottom of the oven. I pulled the oven out, being careful not to put too much pull on the electrical cord. I put a bench in front of the oven and set it down.
I then removed the oven racks, and the plate in the bottom. Bottom element is bake, top element is broil. I unscrewed the igniter, then disconnected its plastic wire connector on the back of the oven, then pushed and pulled the connector into the oven and out the door.
Then I ordered my part for $30 less than Sears from PartSelect, and it got here STUPID FAST. I hooked it up and put everything back together, no big deal, BOOM - Cornbread!

Our oven failed to cook in the Bake mode. I was thinking I needed to have a repairman come service it. I got the product manual & begin to do some research. I thought the problem was was in the control panel until a parts search took me to the Parts Select website where I read the other successful repair stories & the most likely reason it did not work. It was real simple. The only problem I had was a screw that held the ignitor stripped & I had to cut the head off. The directions sent with the part were dead on. I then simply installed new ignitor & presto - it works! My wire connection required stripping the wires & using the ceramic wirenuts. I am glad I found Part Select & will call again when needed!! Thanks !!

My oven would no longer ignite, and I asked a friend to help me see if we could fix it. We found an appliance repair manual online (www.appliancerepair.net), and it described that the most likely part needing replacement was the ceramic igniter - they do wear out, and my oven was - after all - over 20 yrs old, with never a repair! Then, somehow I found this PartSelect website, and after entering the make and model number, it showed the part, with a drawing, and dimensions - enough for me to be convinced it was the right part. I called and was reassured that if it were not the right part, it would be easy to return / refund. So, I ordered the part, standard shipping .... and to my great surprise, it was delivered the VERY NEXT DAY to my front door! And this was right before Christmas, a very busy time! The oven works like a charm now..... (I also had to clean out some of the gas holes, which can build up residues over time.) This repair cost less than $50, I'm sure if an appliance repair person came out it would have been more like $200 - not worth it for an oven this old. So, I'm happy with PartSelect!

During removal of the original ignitor the screws would not come out. they were rusted. using some liquid wrenchI tried to remove them again and they broke. Using an angle drill and special bits I was able to drill out the screws. I re- tapped the holes and the repair was simple. My wiring required additional insulation over the supplied wiring that came with the new ignitor. Cut the wires about 1 1/2 inches from the plug and added the insulation then replaced the plug with the provided wire nuts. Mounted the new unit and all tested perfectly. Closed up oven and operates perfect as if new.

removed door (pull up and out), removed all racks and bottom of oven, removed two screws holding old igniter, unplugged old igniter from harness, mounted new igniter using two screws and nuts purchased from local hardware store, plugged new igniter into harness, replaced bottom of oven and trays, slid oven door down over hinges. Oven works properly. Thanx!

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

1. Removed door by pulling up on it.
2. Removed the floor panel
3. Unscrewed the old igniter
4. Unpluged the igniter from the oven
5. Screwed in the new igniter
6. Plugged in the wire to the oven
7. Put back the floor panel
8. Re-attached the door

remove racks out of the oven. remove very bottom of oven and you will then have access to the ignitor.the part was a little difficult to remove due to the self tapping screws snapping upon removal.drilled them out and installed new ignitor.oven now works fantastic.

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I
attached the new element with the two new screws and connected the two wires and then I turned the oven on and had heat immediately. It's real simple to do..this makes the third time that I have installed this particular part but my Magic Chef wall oven will soon be 20 yrs old. Thank you for making do-it-yourself so easy!!!

This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out. First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle. Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I would like to now say something about the excellent service received from parts select. They have an excellent user friendly site & I received my part the next day.