9875VRV Magic Chef Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Barbara from Newark, DE
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
oven temperature was of & then taking along time to heat
Followed video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wilfred from Hoover, AL
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Oven tempature varies.
We took the back off the stove and unscrewed the two screws from the inside holding the sensor on and pulled it through and plugged it in and then replaced the screws. Very easy. We are still having trouble as the display does not read the same as the tempature is in the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from Bonita, CA
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Top oven sensor
The oven did not auto clean. Problem was the sensor stopped working. Tried to repair from the front but could not get the connector through the hole. Removed the rear panel and found the connector had melted. Could not find a new wireing harnes on line, so I cut the wires on the stove and the new sensor coupling. Spliced the wires togather. The oven cooks fine, I have not tried the cleaning cycle yet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from SEATTLE, WA
- Parts Used:
- 12001656
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Long Oven Sensor failure - oven over heated & shut down
Parts package contained no instructions. Found all instructions on internet. I used Phillips head to remove two screws on anchor plate of Long Oven Sensor. Located at upper left, back corner of oven; access to screws is not simple/easy. Screws back out w/o difficulty. Pull/extract sensor harness through hole[back of oven] which required pushing aside insulation. The harness barely fits thru hole in oven back metal wall; I recommend using needle nose pliers ( which I ended up doing ) for ease of extraction. Disconnect harness plastic interlok clips. Perfect reconnection of new clip harness with ease. Reverse procedure to complete installation/repair. Done in just over 35 minutes due to wrestling with harness extraction through minimal hole opening. Failure occurred on Thanksgiving Day with 22lbs turkey in oven. Top of turkey contacted sensor tip which eventually caused sensor fault; result was scorched upper breast and oven shut down [safety by design]. Cook top was still operative; clock and all readings on digital control panel ceased. With new 'long oven sensor' installed - good as new. Will be sure to buy turkey(s) under 20lbs in future. Jim in Seattle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Cumberland, MD
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
oven not staying on. fault cod F-3 showing
Removed the back of the stove, un-pluged the sensor wires, removed the sensor from inside the oven. installed the new sensor, pluged in the wires, and replaced the back of the stove. A phillips screwdriver was the only tool needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Grantsburg, WI
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Temp spikes.
Remove sensor from oven. Disconnected wire from back. Connected new sensor and reinstalled. Temps now stay stable.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claude from Lakewood, OH
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Oven would not heat
Removed two screws holding oven sensor in place. Haad to remove part of the back to access wires. Found existing wires had burnt up, and had to reterminate same. Installed new sensor, making sure the leads did not come in contact with the rear of oven compartment. (This may have been what caused failure to begin with)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Frederick, MD
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Range had an F-2 code on the control panel
I removed the old thermostat and replaced it with the new one using the supplied wiring adapter for my model of range. Parts Select made this an easy project. Thanksyou
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Globe, AZ
- Parts Used:
- 12001656
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Upper oven shut down after reaching temperature
The hardest part was deciding if this part would fix the problem. The upper oven became unusable. Both elements worked fine until reaching temperature. The oven would not come back on after that. I took two screws out. Then I pulled the wires out and unsnapped the coupling. The install was reverse. I just snapped the coupling in place and replaced the two screws. All works fine now. Saved a couple thousand as wife was prepared to buy a new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty from Hamburg, PA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced gasket around inside door
It was easy because the clips were already on the new door gasket. Just had to remove old door gasket and replace it with the new one. Very simple job.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grant from Alexandria, VA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light bulb failure
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this instruction helpful to you?
Thank you for voting!
Oven have F2 and F3 codes following cleaning cycle making oven inoperable
Remove 2 screws in upper left corner of stove holding sensor in place. Pull sensor out and disconnect plastic electrical connector. Select appropriate adapter (both styles provided with new part) & reinstall. Power up stove and select bake on control unit to test. Works like a charm!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stacey from Tampa, FL
- Parts Used:
- 12001656
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven would not turn on
Watched the video and things went exactly as planned. Love this website will use them again when I need a repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from Newport News, VA
- Parts Used:
- WPW10162384
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
worn gasket
Removed old gasket and replaced with new gasket'
Was this instruction helpful to you?
Thank you for voting!