77EN-5EXWW Magic Chef Wall Oven - Instructions

I drilled two holes on the plate and I did use same original screws.

I just wanted to say once it was installed, It worked great.

Thank you,

Sam

In principle it should be easy to replace the broil element in the wall oven, after unscrewing the supports for the back and front of the element (see other postings for details). The difficulty is with the ground screw, which is inconveniently only accessible from behind close to the back wall of the oven. A very short phillips screw driver is required, but designed so that good torque can be applied for unscrewing and replacing. The newly designed ground connector on the latest replacement elements makes life a little easier, but still be prepared to work slowly and carefully to complete the replacement. Note the new ground screws supplied only work with a flat-blade screw driver, not a phillips-type.

I removed the screws holding the bezel, removed the control panel frame, unhooked the four wires from the timer, and removed the timer. I cut the glue holding the circuit board into the frame and removed the circuit board. I unsoldered the faulty encoder switch, dissassembled the switch, determined the correct specifications for the switch, and ordered the nearest equivalent from an electronics supplier. I modified the new encoder to accept the shaft from the old encoder and I re-drilled the circuit board to fit the new encoder. I then soldered and wired the encoder, reversing the wires to correct the direction of rotation. I then reinstalled everything and added the knob purchased from partselect.com. Now it works. Tough repair - not for the faint of heart or those of average skill. But for the record, installing the knob was of course child's play and took only a moment.

Shut off electricity to oven. Remove existing screws attaching element to back wall of oven. Use pliers to pull off wire connectors. To install the new element, reverse these steps. It's that simple.

I started by removing the door, then trying to remove all of the screws in the oven casing. Of course the very middle screw in the bottom of the oven was rusted and dammged by use. I had to use a drill bit and remove the old screw. After dissasembly of the oven casing, I found that the lip that supports the gasket was rusted and burnt away about 3/4 in. I placed the new gasket in and found that when closed it covered this defect and sealed. I reassembled and cheked for operation.Ok! Imortant--remove the elements before removing oven casing.

Turned breaker off to oven, removed two screws disconnected two wires. Reversed order to install. Piece of cake. Stuart,in va.

Removed two screws. Gently pulled old element away from back of oven, exposing two wires. Disconnected the element from wires by pulling the ends apart with hands. Reconnected the wires with new element. LESS THAN FIVE MINUTES! Saved about a hundred bucks!. (Demo on You Tube.)

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Turn off the electricity for the oven from the switch box. Unsure the damaged element from the unit. Pull it forward and unplug connections. Then plug the new element and use the new screws to screw it back to the unit. That's all

It was very simple. First thing I did was to go online to youtube and type in the kind of repair I intended to do. There were several short videos showing you how to do the replacement.It was easy and took about 30 to 45 minutes. First thing is shut off the power to the oven. ( Very important). You then need to take out two screws that hold the element in place. At this point, just pull the element toward the front of the oven. You will see some insulation at the hole where the wires come out. Slowly work the element forward until you see the fasteners on the wires ( two wires).Disconnect the fasteners and throw the old element out and put the new one in the oven.Connect the element, push everything back into the hole and screw the element to the back wall. You're done ! I had two wall ovens to fix.

We at first thought the replacement could be done by just removing 2 screws.
When in fact it was necessary to pull the oven from the cabinet, remove the rear metal shield in order to unplug the element.
The job went rather smoothly at a considerably less cost than if I had contacted a repair service which would have upped the price of the element plus the cost for the service call.

Unscrewed old element from back of oven, disconnected and reinserted new element and screwed back into place. Voila! So glad to have saved the cost of a repairman. Where I live this would have been a $200 repair(part and service call) easily. This repair took no time at all. Very please as to how fast Parts service got the part to me. I use my oven a lot, so I was lost without it.

I made the mistake of thinking that, if the oven was off, there would be no voltage to the heating element. Wrong! I removed the element, wearing rubber gloves just for safety, and had no problem. But when I put the wiring back on the new element and tried to slide it into the hole at the back of the oven, one of the wires brushed the metal, sparks flew, and melted one of the wires. Even though the oven was off, this wire was hot. The solution was, of course, just to turn off the circuit breaker, reconnect the wire, and slide the element back in. It works fine now.

Turned off the breaker first. Remove the mounting screws and unplug the element. Then replace the new element. Then put in the mounting screws and turn the breaker on. Easy.

I TURNED THE POWER OFF !!! removed the two screws holding the element in place, disconnected the two power wires, installed the new element. Done, in less than five minutes.