Models > MA2120B

MA2120B (ABKEGSE) LG Wall Oven

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for MA2120B

Viewing 6 of 6
Keep searches simple, eg. "belt" or "pump".
Rated at 20 amps and 250 volts, this microwave time delay fuse protects against electrical overload. It accommodates the brief current surge at startup but opens the circuit during a sustained overloa...
In Stock
Order now and your part arrives by Nov 28
$6.51
In Stock
Order now and your part arrives by Nov 28
On Order
$134.28
Convert power from the microwave?s high-voltage circuit into the microwave energy used to cook and warm food with this magnetron. A failed unit may stop heating even though the fan, turntable, and dis...
In Stock
Order now and your part arrives by Nov 28
This microwave high voltage diode and cable assembly is used to allow current to flow in one direction, working with the transformer and capacitor to supply power to the magnetron. That power enables ...
In Stock
Order now and your part arrives by Nov 28
Special Order
No Longer Available
$43.92
Electrical energy stored and released by this microwave high voltage capacitor helps power the magnetron that heats food. It works with the transformer and diode as part of the high voltage circuit. T...
In Stock
Order now and your part arrives by Nov 28
In Stock
Order now and your part arrives by Nov 28
$54.12
This glass tray provides a stable, heat-resistant surface for cooking or heating while allowing even energy distribution. It is replaced when chipped, cracked, or missing to restore safe operation.
In Stock
Order now and your part arrives by Nov 28
Special Order
In Stock
Order now and your part arrives by Nov 28

Common Problems and Symptoms for MA2120B

Viewing 3 of 3
No heat
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Won’t turn on
Fixed by these parts
Fixing
How to fix it
Tray won’t turn
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Joseph from WILTON, NH
Parts Used:
6324W1A001L
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Magnitron failed
Over the stove microwave installed in top cabinet row.
1. Unplug device.
2. Two people to remove from wall/cabinet (remove two, large, top mounting screws and rotate entire microwave down and off the wall mount). Should be some wood spacers between top of device and bottom of cabinet.
3. Remove screws from sheet metal cover .
4. Remove one screw holding blowers in place and rotate out of the way, in order to gain access to 2 of 5 screws that hold the magnetron in place.
5. Unplug magnetron and remove the 5 screws.
6. Drop in new magnetron and re-assemble microwave in reverse order (steps 5-3).
7. Two people restore micro to wall/cabinet. Replace wood spacers, re-install two, large mounting screws (finger-tight). Test device. Secure the two large screws.
8 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from NEWARK, DE
Parts Used:
6324W1A001L
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
Would not heat and made a buzzing or popping sound
Unplug the microwave. Remove the Philips head and safety Torx head screws along the bottom of the sides and rear of the microwave which hold the black cover on. Lift the cover up at the rear and slide it backwards to disengage the tabs on the front top. Remove the cover. Discharge the capacitor by shorting the terminals to each other and then ground. Do this with a well insulated object and be aware there may be a pop when you do this. Keep hands, etc. on the insulated part of the object (screwdriver handle, etc). There's a lot of stored energy in that capacitor. I'd advise first checking the diode to make sure its not bad. Replace it if it is. The Magnatron is held in with a couple of screws on the top and sides. Unplug the connector and remove the screws. Remove the Magnatron. Installation is the reverse of removal.
4 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Stacie from Granbury, TX
Parts Used:
6324W1A001L
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Microwave would not heat. Convection still worked.
I verified I had 120 volts going into transformer when the microwave was supposed to be running. The capacitor and HV diode both tested good. Be sure to discharge the capacitor before working in this area. This isolated trouble to either the transformer or magnetron. The windings of the transformer measured good. So ordered a magnetron. I t was very easy to swap. There were 4 screws and one connector. This fixed our microwave.
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!