KEBK101BBL01 KitchenAid Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- patrick from Colleyville, TX
- Parts Used:
- WP74008369
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Sensor went out after fire in oven fault code 1b11
I removed the 2 screws holding the sensor in the back of the oven and pulled the wires out. The connector got hung up in the insulation. Rather than pulling too hard, I loosened up the heating element plate and screws and pulled the whole plate out an inch or so so I could work the connector through the insulation. I forgot to shut off the power. When I put the sensor on, I got the same error. I briefly shut off the power at the breaker and turned it back on. The clock on the oven did not reset. It still didn't work. So I took the whole thing out, shut off the power, reconnected it, turned the power back on, reset the clock, and it worked! Should have turned the power off first and I wouldn't have had to do it twice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JULIE from SPOKANE VLY, WA
- Parts Used:
- WP74008369
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Water spilled in oven shorted out the sensor-code 3D21 I think
Didn't need sensor replaced. After turning the breaker switch back on oven appeared to be working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Carbondale, CO
- Parts Used:
- WP4449751
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
upper oven of wall oven would not heat suspected high temp limit switch
removed unit from cabinet tested switch it was OK checked wiring and found shorted out wire leading to switch. cut out bad section and spliced wire back together
problem solved
problem solved
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dan from Gallatin, TN
- Parts Used:
- WP74008369
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Socket set, Wrench set
oven had error messages
I tryed to remove the sensor from the oven by removing the screws inside the oven. Unfortunatly, the plug for the sensor would not reach the inside of the oven. I had to remove the oven from the wall and remove the back cover to ac3ess the sensor wiring.
After that it was a snap.
After that it was a snap.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alan from DENVER, CO
- Parts Used:
- WPW10335920
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inner glass door on oven was broken
Simply unscrew four small screws on the top aluminum cover plate ((two on top and two on the side of the plate) and the glass easily slides out and is replaced with the new glass. Once the glass is replaced, you simply screw the cover plate back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beth from NEW YORK, NY
- Parts Used:
- WPW10335920
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
I turned on the oven self clean function and the inner glass cracked
Super easy repair! I slide the old glass out and was able to clean all 3 layers of glass which has been driving me crazy for years. To install the new glass required unscrewing and screwing in 2 screws. If I had waited for a repair person, it would have been one month. Instead the new glass came in a couple days and the repair took 15 mins (cleaning took longer, haha).
I highly recommend doing this repair yourself.
I highly recommend doing this repair yourself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Scranton, KS
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Terminal block arc'ed because a wire had become loose.
Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robin from Vanderbilt, PA
- Parts Used:
- WPW10245259
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
I had a power serge and it burned the Plug at the termial block and melted a few wire.
After we got the part in the mail my husband put it on and shortened the wires and put new plugs on the ends of the wires and we had to get a new plug put it on and it was fixed.
Was this instruction helpful to you?
Thank you for voting!