NHP01MCG KitchenAid Wall Oven - Instructions

Killed the power to oven, removed oven from its enclosure (its heavy), removed back off oven and the part that needed to be replaced was right there. After that simply reverse the procedure. Honestly hardest part of whole job was remembering what i did with the screwdriver after my last home repair job. The oven is heavy you may need help.

good, could you please e-mail me a copy of inv.,lost track of mine and need copy for re-imbersment

Unscrewed the old thermostat took off the conectors then replaced with new one, and screwed it back on.

I looked up the meaning of the error codes and determined that the temp sensor was malfunctioning. Looked on line for a sensor and found what I thought was the right one and ordered it from PartSelect. The sensor arrived three days later and I removed the old sensor (with some difficulty I might add). Then I discovered the connector did not match. I called PartSelect and found out that the sensor connectors had changed since the oven was built and that an after-market sensor with the right connector was available. I ordered the new one, returned the wrong one and the new one arrived three days later. I popped it in and now I have a working oven.

First thing- Don't be afraid! It took me way longer to clean the old door parts than to do the actual replacement. First take the door off by opening it fully and sliding a round piece of metal ( I used a 16d nail) in each hinge mechanism. close the door about 3/4 of the way and pull up. Th door comes right off. Just keep undoing screws until you get down to the layer of glass you need to replace, then reverse the process. If you're replacing both the hinges, note that both the pins used to hold the hinge open come out the right side.

Have a Whirlpool Accubake self cleaning wall oven that quit working after doing a cleaning. Found that the thermal overload safety thermostat might be the problem. Ordered the part which arrived in a couple of days. Installation was very easy and took about 10 minutes. First turn off power to the oven. Slide the oven out, remove the back panel, remove the old safety thermostat which has two wires coming off of it, and replace it with the new one. Put the back panel on and slid the oven back in. Turned the power to the oven back on and we had heat. Problem solved.

Contacted repair person on line and explained the problem. Person suggested testing the thermal fuse. Checked for continuity and there was none indicating the fuse was blown. Ordered new part and installed. Everything working again. Only problem was that the new part did not have the same connection as the old one on one end. Made substitution and it worked.

Repair was fast and easy, door closes like new.

The Kitchenaid oven has 2 interior oven lights. They are behind rectangular glass panels, in an assembly housing The repair is pretty simple. Shut off the power at the breaker box to the oven first. First remove the small screw that holds in the assembly with a Phillips screwdriver. Put down a white piece of paper towel to catch it in case it drops. It is grey color and hard to find against the bottom of the oven. This will free up the assembly and you can move it out. There is a wire on the back so it only comes out a short distance. Next the glass panel covering the bulb must be removed. The small metal clamp with 2 projections that act like a spring to put tension on the glass. Gently pull this out parallel to to the glass and it will release the lens. The old bulb is a simple 2 prong halogen that pulls out easily. Replace it with the new bulb carefully pushing the prongs in. If you did not turn off the power the light will come on immediately. it will get hot quickly so don't touch it for more than a few seconds. Next slide the glass lens back into place into the back of the assembly. Slip the other clip with the screw back on the front. Replace the assembly back into the oven side opening. Secure by replacing the small screw removed in the beginning. You are done. It is about a 5 minute job start to finish. I would replace both bulbs even if only one went out because the other one probably will go out a short time later and you will have to go through this again soon. Oh, and cheap bulbs are not worth it. They are very dim and burn out quickly. Go with the better bulbs you get from PartSelect.

You need to replace both the left and right springs. Open the door completely, . Insert a short screw in each pin hole on each spring bracket.slightly lift the door and pull out. remove the four screws that secure the front panel. Remove the four screws that secure the springs. Install the new springs and replace the front panel. Replace the door assembly into the oven, remove the pins that were shipped with the hinges and you are done.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

Lower the oven door. Insert the locking hinge pins. Pull the door away from the oven. Remove the 4 screws, 2 at the top and 2 at the bottom, to remove the front panel. Remove the 4 screws that secure each left and right spring. Remove the old springs and install the replacements by reversing the procedure. Remember to purchase 2 springs.