KEBS277DBT10 KitchenAid Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Linda from Hilton Head Island, SC
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Cracked Door glass
Ordered the glass and read the other reviews/instructions on the PartSelect site. Also read the instructions in my owner's manual for removing the oven door. The hardest part of replacing the glass was the removal and replacement of the door. Once I had the door out, replacing the glass was as simple as removing about 8 or so screws, lifting off the cover and replacing the glass, then replacing the screws. One of the hinges on the door had closed and I was not able to open it to replace the door, so I had to have a neighbor come over to over his muscle power. The hinge problem should not have happened and without that little issue, this is a simple repair that I'm sure saved me at least $100.00 on repairman! And - I'm a woman!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Raymond from BLOOMINGTON, MN
- Parts Used:
- 4396923
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Purchased home but stove had no broiler pan.
Purchased 2 piece broiler pan from this site
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Amanda from Indian Harbour Beach, FL
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Cracked inner glass of oven
I used the instructions from another user on this site and the instructions were great. First look in your oven manual to see how to get the oven off-hardest part of repair. Before removing door-duct tape the broken glass. Remove door. Lay door down on flat surface and keep track of screws as you take them out. Remove outer liner-we removed 6 screws total. Replace glass with new glass. Reattached outer liner back onto door. Replace door. This is a GREAT site. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from San Diego, CA
- Parts Used:
- WP9759242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Oven Would Not Heat After Auto-Clean
Very simple. I removed two screws holding the oven in place. Slid oven out onto the kitchen floor - it doesn't really weigh that much. I then removed about a dozen screws holding the back panel in place. I removed the back panel, disconnected the thermostat by unscrewing a single screw and pulled the defective part from the connectors. I then installed the new thermostat, screwed the back panel back on, slid the oven back into place and re-secured with the two screws. Voila! Repair done. The whole procedure took about 15 minutes and was not difficult at all.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dallas from Andrews, TX
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
broken glass door
Took longer to take door off than replace glass.The door would have come off easy if I had read the instructions that came with the oven
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Lambertville, MI
- Parts Used:
- 4451896
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Oven door latch would self-activate the door-lock feature for all operatons making it impossible to use the oven
My electric oven is a built-in. First I turned off power to the oven.
Then, I removed the oven door as instructed by Kitchenaid, next I removed the screws that held the concealing-sleeves on each side of the oven opening. Slid down the sleeves, loosened the exposed screws on each to allow the oven to slide out. Slid the oven out abut half way to expose the top. Removed the metal sheeting from top of oven to expose area where door latch assembly was secured. Removing the sheeting was made easier by removing the screws on each side of the control panel and lifting the panel out of the way.
The latch assembly is held in place by two screws through the front of the plastic venting. Identified the connections to appropriate points before I removed the wiring, removed wiring and attached to points on the new latch assembly.
Secured latch assembly to plastic vent, secured sheeting to top of oven, placed conrol panel back in place, pushed oven back and secured with screws.
Slid sleeves into position, secured with screws and replaced oven door.
Then, I removed the oven door as instructed by Kitchenaid, next I removed the screws that held the concealing-sleeves on each side of the oven opening. Slid down the sleeves, loosened the exposed screws on each to allow the oven to slide out. Slid the oven out abut half way to expose the top. Removed the metal sheeting from top of oven to expose area where door latch assembly was secured. Removing the sheeting was made easier by removing the screws on each side of the control panel and lifting the panel out of the way.
The latch assembly is held in place by two screws through the front of the plastic venting. Identified the connections to appropriate points before I removed the wiring, removed wiring and attached to points on the new latch assembly.
Secured latch assembly to plastic vent, secured sheeting to top of oven, placed conrol panel back in place, pushed oven back and secured with screws.
Slid sleeves into position, secured with screws and replaced oven door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from VIENNA, VA
- Parts Used:
- WP4455381
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Worn door gasket, leaked steam while cooking
Used a Phillips head screw driver to remove cover that was covering the over bottom 1/3 of the installed gasket. I then used flathead screwdriver to help remove gasket from the "pins" that were in the gasket that held it to the oven. Installed new gasket inserting pins into the oven. Then I installed cover over bottom 1/3 of gasket. Overall process was very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from BUFFALO, NY
- Parts Used:
- WPW10131825
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
bUILT IN OVEN NOT COMING UP TO TEMPERATURE
Replaced oven temp sensor, removed oven door and interior racks for easy access to oven upper rear sensor access. Used philips head screw driver to remove both screws, gently pulled old senor out of reat oven wall until electrical connector clear of rear wall, disconnected connector, connected new sensor and gently pushed wiring and connector back into opening, reinstalled door and racks. Ran open thru cycle and used oven thermometer to check temp. fast easy install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Milton from Pasadena, TX
- Parts Used:
- WP4449253
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
inner oven door glass was cracked
Removed the door and laid it flat with the cracked glass facing up. applied duct tape to the broken glass to help hold it together. Removed the screws from the frame holding the glass. lifted the frame off,removed the broken glass and replaced it with the new piece. replaced the frame. and put the door back on the oven.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dana from Black Mountain, NC
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Loose terminal caused block to overheat and break
Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- david from SOUTHAVEN, MS
- Parts Used:
- WP9760588
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
oven light would not come on
cut power off and placed sturdy table same height as bottom of oven in front of oven. removed trim screws. pulled oven out onto table. removed top cover and panel on left side . tested transformer to be sure it was bad. then replaced transforner
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILBERT from LOS ANGELES, CA
- Parts Used:
- WP4455334
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
TOP BLOWER FAN NONFUNCTIONAL
1- TURN OFF POWER TO OVEN
2- REMOVE OVEN
3- REMOVE BACK PANEL SHROUDING
4- DISCONNECT POWER TO BLOWER
5- REMOVE BLOWER UNIT
5- REPLACE WITH NEW UNIT
6- RECONNECTED POWER
7- PUT OVEN BACK
2- REMOVE OVEN
3- REMOVE BACK PANEL SHROUDING
4- DISCONNECT POWER TO BLOWER
5- REMOVE BLOWER UNIT
5- REPLACE WITH NEW UNIT
6- RECONNECTED POWER
7- PUT OVEN BACK
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- carlos from Holtsville, NY
- Parts Used:
- WP9759242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Wouldn't heat after a cleaning cycle run
I first did a search with my issue, found out there were many others with the same issue. That then led me to see the part, a fuse / thermostat, was the culprit and easy to replace it seemed. But first called a service co. who confirmed my findings, and quoted a fix of a $2-300! So I bought the part; worse case I'd have someone else install. The web site noted the few screws to remove and a key suggestion to find a box of same height to easily slide out oven; I used a porter cable nail gun case which worked great. Took my time removing trim, mounting screws etc., slid out oven easy. Removed back plate and there was the older one. Removed and installed new in a minute. Spent more time cleaning around trim than actual install. What a great day it was. Wife was happy too!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- edward dennis from cocoa, FL
- Parts Used:
- WP9759242
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
After selfclean cycle, oven stopped getting warm
First I cut off power ! 2 screws for oven trim,4 more to disconnect from cabinet. Hardest part was pulling oven out and pushing back in. I found a big box of correct size to rest it on so I didn't need to disconnect the powerline. 8 more screws to remove the back panel. 2 screws to remove the thermostat.Then put it back together. New part had arrived sooner than expected, cost of the part was less than a minimum service call would have been! I absolutly will use your site again.PS Wife was amazed and now thinks I'm a genious.
Was this instruction helpful to you?
Thank you for voting!