KEMS377BWH2 KitchenAid Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Rubye from Garland, TX
- Parts Used:
- 4365564
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Flanges broke on Button
All I had to do was slip the two springs onto the outside hubs and push the Button into place on the Microwave. So easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ivanka from Atlantra, GA
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
burned oven bulb
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Schwenksville, PA
- Parts Used:
- 8009
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Billy from Tuscaloosa, AL
- Parts Used:
- 4365565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Button and spring popped out each time you closed the door
When we received the part, it had an extra little tab on it which had no place to fit in our microwave. We were able to saw the extra tab off, place it (with the spring) in the opening, and it worked!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Gaylord, MI
- Parts Used:
- W11594027
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
oven light not working
replaced light socket but did not repair problem. must have burned the motherboard.
pleased with service from your company.
pleased with service from your company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Ada, MI
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light bulb went out in my oven
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Crimora, VA
- Parts Used:
- WP8203546
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Block broke
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Caddo Mills, TX
- Parts Used:
- W11594027
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Inside Light would not work
Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charlie from Irvine, CA
- Parts Used:
- 4365565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
One of the push button retaining clips broke off.
Opened the package,removed the push button. Slid the three return springs onto the three plastic "prongs" located on the back of the push button. Placed the push button and springs into the retaining hole and pushed into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary W from Mill Creek, WA
- Parts Used:
- 4365565
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Button to open door broken
Simply set it inot the hole. Absolutely not big deal and now the door opens as the applicance was created to. We no longer have duck tape holding a boken one in place. I wish I knew of this website earlier.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- peggy ann from forest city, NC
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
replaced oven lightbulb
very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shirley from Las Vegas, NV
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light burned out in upper oven
Screwed in light bulb and glass protector
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judith from Phoenix, AZ
- Parts Used:
- 8009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb Replacement
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- RAYMOND from JACKSONVILLE, FL
- Parts Used:
- 4396923
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broiler pan missing
ordered new broiler pan
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Santa Ana, CA
- Parts Used:
- WP661416
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Replaced Bake Element
FIRST: I Shut off the circuit breaker to the oven. Then: 1. Removed convection-fan cover (it was partially blocking the bake-element screws). 2. Unscrewed 2 bake-element screws. 3. Pulled old bake element forward to expose connectors. 4. Disconnected both connectors and discarded the old element. 5.Connected the new element and pushed it in so that plate was flush against the back of the oven. 6. Re-installed the 2 element screws. 7. Re-installed convection-fan cover. LASTLY: Turned on the circuit breaker to the oven and baked a cake! IMPORTANT: The original screws can be very, very tight. When removing them, be sure to use a socket wrench or other tool that gets a firm grip on the hex heads, or you could round the corners of the heads, permanently damaging the screws.
Was this instruction helpful to you?
Thank you for voting!