KEMS306XAL6 KitchenAid Wall Oven - Instructions

1. Open the oven door (about 4 inches) until it hits that first spot that it stays open by itself. 2. Put a pin or small screwdriver in the tiny hole in the hinges - this will keep them from snapping back and also make it easier to put the door back on. 3. Pull up on the door until it comes off the hinges. 4. Lay the door on the table with the inside down - remove the 2 screws from the top of the door and the 3 screws from the bottom - pull cover off and lay to the side. 5. Use nutdriver to remove next panel - they are located under the strip of foam along the sides, 2 on each side. 6. Use nutdriver to remove 6 screws around the pane of broken glass. 7. Replace glass then do steps in reverse to get the door back together. 8. Slide door back onto the hinges, remove the pin or small screwdrivers from hinges. Voila! New glass, no problem!

FIRST: I Shut off the circuit breaker to the oven. Then: 1. Removed convection-fan cover (it was partially blocking the bake-element screws). 2. Unscrewed 2 bake-element screws. 3. Pulled old bake element forward to expose connectors. 4. Disconnected both connectors and discarded the old element. 5.Connected the new element and pushed it in so that plate was flush against the back of the oven. 6. Re-installed the 2 element screws. 7. Re-installed convection-fan cover. LASTLY: Turned on the circuit breaker to the oven and baked a cake! IMPORTANT: The original screws can be very, very tight. When removing them, be sure to use a socket wrench or other tool that gets a firm grip on the hex heads, or you could round the corners of the heads, permanently damaging the screws.

We looked at SEVERAL postings on this site. We ARE NOT DYIers. The descriptions on how to do this repair were super helpful. When we read that it only took 30-minutes and was easy, we thought, "Well, they haven't met us!" On the contrary, we got through this without one marital issue. It did take both of us and was kind of like a puzzle. It took us somewhere between 30-60 minutes. We left the door on and worked our way through screw by screw, panel by panel and "voila!" -- we were able to turn on the oven that night without it exploding!! Thank you Part Select and all of the DYIers that post on this site!

I read how two others had fixed thiers on this site. Put a nail in each hinge then lifted door strait up off hinges and laid it on kitchen table. removed 9 screws around door. Lift inner door up. remove 3 nut head screws on each side and lift that shield up and out. replaced glass and the put it all back to gether. saved my self a good 200.00 plus dollars. thank you soo much. I will be back if I need anything else..Brenda..

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

followed the instructions u sent me

Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

I very simply replaced the gasket where it belonged and I was good to go!