KEMS306XAL5 KitchenAid Wall Oven - Instructions

Was fairly easy to take door off, and apart. Multiple layers of glass in the door, which all needed cleaning, but re-assembly was rather easy. No tricks or short cuts!

Turned off CB for the oven,Remove the oven from the cabinet , remove the back of the oven, replaced the light Assembly. turned on CB for the oven, tested the light. and truned off the CB and replace the back and reinstalled the oven in the cabinet.

The information provided us through other customers really helped us. My husband is NOT a handyman and does not like to do these type of jobs. However he decided to attempt it. He likes step by step instructions from the company, however following other customers advice worked great. We where real pleased with how quick we received the replacement glass.

First I read some of the other tips provided by the others in order to make it easier for me. I put a of couple of nails on the hinges (in the holes) to prevent them from springing back into the oven. I took the oven door off carefully and laid it on an area rug. Then I took the door apart. I did it slowly so that I wouldn't forget how to put it back together. It wasn't difficult; it just took a little bit of time. So happy that I was able to do it myself. I'm sure I saved quite a bit a money by not having to call an appliance repair shop to do it for me.

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

All the electrics worked on Amana microwave EXCEPT for the cooking function. Inspected the control board and found the upper switch on the door interlock was burnt. Installed new switch in minutes and everything now works fine. Unfortunately, had to purchase expensive two switch "kit" although only one switch was kaput. PartsSelect mailing was SUPER fast. Thanks for looking, Scott

After unplugging the microwave and removing the screw, I removed the old bulb and put in the new one!! I made sure it was in securely and the difference in the light was awesome! I use this light when I bake bread and let it rise inside the microwave, but DO NOT turn it on. The heat from this light helps the bread to rise properly!!

Removed the light cover - unscrew the bulb - place the gasket on the base of the light cover - replace the bulb - replace the light cover

followed the instructions u sent me

Since others reported similar problems and it was just the fuse we tried that first. That wasn't the problem so we ordered the Door Interlock Switch Kit. Shipping was very fast! Our microwave had 3 switches. My husband asked how to know which one to switch. I read that one person just did process of elimination. Luckily ours worked on the first change out! So happy to have stumbled across this site and not have to buy a whole new microwave.

Remove the 3 Phillips screws along the bottom of the door, 2 screws on the inside and 2 screws on the top edge near the handle. Take off the outer door. Clean out the dust etc with a Vac. Tape the inner glass to the inside of the door so it doesn't slip loose later. Close the door. Remove the 4 screws under the foam to take off the middle window asm, not the 4 screws holding just the middle glass. Now when you remove this assembly the inner glass is not supported(this is why you taped it) so do not jar or lower the inner door yet. Now that the middle assembly is off support the inner glass with one hand and lower the door. Remove the tape and remove the glass. Now install the new glass being careful the gasket is in place. Reinstall everything in reverse.

1. Open the oven door (about 4 inches) until it hits that first spot that it stays open by itself. 2. Put a pin or small screwdriver in the tiny hole in the hinges - this will keep them from snapping back and also make it easier to put the door back on. 3. Pull up on the door until it comes off the hinges. 4. Lay the door on the table with the inside down - remove the 2 screws from the top of the door and the 3 screws from the bottom - pull cover off and lay to the side. 5. Use nutdriver to remove next panel - they are located under the strip of foam along the sides, 2 on each side. 6. Use nutdriver to remove 6 screws around the pane of broken glass. 7. Replace glass then do steps in reverse to get the door back together. 8. Slide door back onto the hinges, remove the pin or small screwdrivers from hinges. Voila! New glass, no problem!

FIRST: I Shut off the circuit breaker to the oven. Then: 1. Removed convection-fan cover (it was partially blocking the bake-element screws). 2. Unscrewed 2 bake-element screws. 3. Pulled old bake element forward to expose connectors. 4. Disconnected both connectors and discarded the old element. 5.Connected the new element and pushed it in so that plate was flush against the back of the oven. 6. Re-installed the 2 element screws. 7. Re-installed convection-fan cover. LASTLY: Turned on the circuit breaker to the oven and baked a cake! IMPORTANT: The original screws can be very, very tight. When removing them, be sure to use a socket wrench or other tool that gets a firm grip on the hex heads, or you could round the corners of the heads, permanently damaging the screws.

We looked at SEVERAL postings on this site. We ARE NOT DYIers. The descriptions on how to do this repair were super helpful. When we read that it only took 30-minutes and was easy, we thought, "Well, they haven't met us!" On the contrary, we got through this without one marital issue. It did take both of us and was kind of like a puzzle. It took us somewhere between 30-60 minutes. We left the door on and worked our way through screw by screw, panel by panel and "voila!" -- we were able to turn on the oven that night without it exploding!! Thank you Part Select and all of the DYIers that post on this site!