KEBS208DBS8 KitchenAid Wall Oven - Instructions

Repair was very easy, Alittle time consuming. Unscrewed the outer skin of the door and removed the pieces.

1) Look for the part at partselect.com, make sure you have the model and part number ready. Once you find the part, don't order yet. 2) Start your do-it-yourself repair by removing the oven door. On each side below are two arms/hinges, look closely and you will find locks on each side. Use your finger or flat screwdriver to slide towards you (this is where you start clicking your camera in evey step). Once you did it, wiggle the door a little bit, make sure they're unlocked, then pull it out carefully and hold it tight since it's little heavy. 3) At this point, you only need the phillips screwdriver. Look for all the screws, and unscrew it all, one step at a time (again make use of your digital camera). Remove the parts one at a time until you take out the broken inner glass. Measure it against the dimensions shown in the partselect.com. At this point you feel comfortable putting it back in-reverse, then you order the part. It took me 3 days for the part to arrive, but it's no big deal. 4) It's a bit difficult for me the first time, I can't figure out how to put them back (that's why I recommended the digital camera), plus I have to clean the inside and the other two glasses so it took me 1-2 hrs. I assure you if you follow my instructions, 15-30 minutes max, no sweat. 5) My wife promised me $300 for the labor (competitive price), I'm still waiting though.....Good Luck

I ordered the part online and after recieving it I downloaded the manual from kitchenaid online and it explain exactly how to replace this part and I followed the instructiones and it worked with not too much difficult . It took me about an hour between reeding the instructions and doing the job itself

Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.

opened door and secured the open position with a 3/8 allen wrench through the hole at the base of the support arm. (small bolt or other round, short object can be used). This locks the door in a 75% open position. Locking the door open allows easy lift and removal. Six screws and the door is apart. Clean and reassemble.

Unlocked the latches that hold door into oven. Removed door to work on it. Disassembled door by removing all the screws that hold it together. Removed two other glass sheets to access location. Cleaned out broken glass. Installed new glass sheet and reinstalled two other glass sheets. Reassembled door and reinstalled in oven. Not difficult, just a fair number of parts and pieces to take apart and put back together.

I first removed the door from the front of the oven according to instructions that I found on the Internet from others that have had similar problems. I then removed a total of 8 screws - 4 that were holding the door together, and 2 each for the two hinges that I replaced. After replacing the hinges, I re-installed the 4 screws and then guided the oven door back into place. It took probably about 20 minutes from start to finish, and the news hinges that I purchased solved the problem perfectly.

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

Door repair assembly was simple, did without any instructions or manuals. Fan assembly, the actual fan replacement was easy, it was the number of pieces of metal that needed to be removed i order to get the main rear panel off to access. Also had to remove panel from inside the oven; requires two people to loosen screws from inside while the other person holds the fan assembly from the rear side of the oven. Didn't have any instructions for this task either, figured it out anyway, just follow the layers.

Hardest part was getting the oven door off. Since I bought this house with oven already in place, I had no owner's manual. Tried to get it off with tips found on this site, no go. Went online and found the manual which said to insert allen wrench in holes in hinge, then lift up FROM THE BOTTOM. That is the key. Got door off, then found that replacing the inner glass is a multi step process that starts with the outside door, then multiple brackets to the next inside glass, then more braces to next glass, then finally you are at the broken (inside) glass.My advice would be to take pictures on cell phone or whatever of each level, so you know what goes where when you put it all back. I figured it out but would be faster with a picture. Anyway, got all together and the oven works fine, door looks great!.

To prevent this from happening use 7 #8 flat stainless steel washers per the 4 oven door holes that connect to the the handle as shims before securing the attachment brackets.

Ordered a replacement part and during installation tightened the top mounting screws too tight and shattered the replacement part. Ordered a new replacemnte part and installed without overtighting mounting screws. Repair went well. I caution others not to overtighten top mounting screws. These are same screws that attache the SS pull handle on oven door.

The replacement door has a cushion on the top and the sides secured to the tempered glass. When you tighten these brackets they can cause the entire glass panel to break. To prevent this use seven #8 flat washers per hole on the top of the door before securing the brackets. These will act as spacers but you will still will be able to achieve enough pressure to hold everything in place when you tighten them. Hope this helps, it worked for me, florida bob!!

good, could you please e-mail me a copy of inv.,lost track of mine and need copy for re-imbersment

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!