KEBS278DBL4 KitchenAid Wall Oven - Instructions

First, I'll say this website made it easy to find and order the part, it arrived quickly and reading others' reviews helped with installation. My Dad and I did the repair together, which really helped - my Dad is an fantastic handyman! We removed the door by lifting it up out of the hinges - a little difficult to get the right angle, but we succeeded with a little wiggling. We disassembled each later of glass/door, keeping each layer in order with screws so we could retrace our steps. I cleaned each layer thoroughly, which added to the time. Unfortunately, just as we were putting the last part on (exterior door with glass), the glass shattered as I tightened the screw! Ack! My Dad said it's because the glass was old and easy to shatter. Maybe I tightened the screw too much? So, back to the website I go to order the next part. We expect it to arrive soon. The bad news: another Christmas without an oven. The good news: my oven is now clean as new (I even removed the back fan cover to clean the fan - couldn't have done that without removing the door) and the parts added up to a fraction of the cost of a new oven.

There are hinges on the door that need to be lifted up to take the entire oven door off the appliance. The screws are taken off of the door to get to the interior glass. The cracked oven door was simply taken off and replaced by the new one and the screws were put back and the door was placed by hooking it onto the appliance and the hinges were dropped down. Simple as that!

My mother and I were having considerable trouble baking or using the wall oven due to the escape of heat because the door wouldn't close properly. She, on many occasions, rested heavy baking pans/sheets on the door which, over years, caused it to "spring". Before I started the project I took a level and saw the door was facing down at least 3/8"-1/2" more than being level. I assumed it was the Door Hinges and after much research I found PartSelect who was extremely helpful in not only advising me as to the exact problem causing the door to not close properly but also in the ordering process itself. Because of the complexity of how the door is assembled I took digital video at various stages: removal of the door, disassembly of the entire door, removal of the control panel, and various small parts of the door - all with audio description by me as I went along. Because it took a few days to order and receive the parts I had time to clean the baked-on, caked-on grease inside all the parts to include the vents on the door and under the control panel using a power-washer when possible. I obtained auto-strength grease cutter/remover and soaked every "group" of screws in separate glass jars with covers (labeled). I also taped screws to a piece of paper, traced them to make sure they went back in the same place, and washed these as I went along. At the time the parts were received they were packaged in a fantastic way - quick shipping, easy to order, and I immediately started to reassemble the door. When I found my video wasn't enough to help me get the door assembled properly I used .pdf files I found on PartSelect which were extemely helpful and with a laptop close by I referred to the video I had taken and also SmartSelect's .pdf files. Because my digital camera was - and is now defective - I lost some of the most important video and this is the reason it took me almost 5-1/2 hours to reassemble the door. I wanted it to be correct given the oven is self-cleaning plus I do not want fires in the house!! All parts were laid out across three rooms and after being like this for almost a week it was great to have the entire oven back together again. At this point the oven door, when opened, is now facing "up" at least 3/4" as opposed to hanging down as it was before this project started. I closed the door and it actually pulled itself shut - something it hadn't done in years! The hinges came with pins already inserted so I didn't have to wrestle with the hinges to insert the original pins. The gasket was the easiest part to replace - simple removal of the old, worn, charred one and pop in the new one using the little clips that came on the hinge. The hinges themselves are extremely strong and well-made. After this project I have to say the oven now looks BETTER than when purchased, my mother has used it to cook with only once and it took 1/2 to 3/4 the time given the door is now completely closed because of the new hinges. I am totally satisfied with the parts, with PartSelect, will keep this site as a reference for further replacement parts if needed, and the oven is positively GORGEOUS after it was thoroughly cleansed of built-up grease. It looks BETTER than a new oven!! THANK YOU, PARTSELECT, for all your help and perfect parts!!

I followed these instructions put in by a fellow customer. These were very helpful. Just make sure the glass is finger print free before you put it all back together. My time was 30 minutes end to end. =========================== The first thing I did was to remove the oven door by releasing the two latches on the hinges (by hand). I then raised the door toward the vertical position and lifted up. The hinges slide out of the oven housing. I laid the door, inside face up on my island counter top. This ensures that none of the parts will fall when disassembling the door. Next I unscrewed the screws 4 top and bottom and four on the inside face. This releases the frame from the front housing. Lift the frame off the door, exposing the glass pieces. Lift off the broken inside glass and place the new piece in the glass retaining housing. Replace the outside frame and replace all screws. Take door back over to oven and slide hinge bottoms back into slots on oven. Rotate to horizontal position and flip latches back to locked position. Total time was about 10 minutes mainly because I was curious how the door was constructed and I poked around while it was disassembled

When the oven is installed, there are two pins on the replacement hinges that are removed. If you were like me, you tossed these pins so you need to take a large nail and cut a 3/8" of material to replace these pins. This will allow the door to be removed when you open it half way. This is the most difficult part of the repair since you need to carefully pull the door off and a precise angle with an upward pull from the bottom. You will notice the new hinges have these pins so you can also try to get some new pins at a hardwire store that are similar. Next, you need to careful set the oven door down on a smooth work area and remove all of the philip head screws. The front of the door will be remove from the inside door piece by slipping it up a little when the screws are removed. The two screws that are on the inside panel hold the hinges. Take note of how you remove these since you will do just the reverse in putting in the new hinges. It would be a good idea to take the glass section off and clean it if you want to take on the extra challenge but you need to be very careful not to break these and that you put them back that same way it was removed. Now that you have it all put back together, you simply install the door back the way it was removed and then you can open it all of the way down to remove the pins in the hinges. Now would be a good time to put these pins in a save place with the rest of your paperwork for any further removal.

Getting to the wiring harness behind keypad discovered a blown in line thermal fuse. Replaced and turned the main breaker back on. Clock & controls back on.

Had to screw off old terminal block & screw on new one