YKEBS208DS6 KitchenAid Wall Oven - Instructions

I removed the two stainless trim pieces (2 screws) and then two screws which hold the oven frame to the cabinet. Be careful to put a pad on your floor before you pull the oven out of the cabinet as there are sharp edges on the bottom of the oven. I removed apprximately 12 screws holding the back panel in place. The fixed set point thermostat is in middle toward the top of the oven cavity after removing the rear panel. Just remove two screws and slide the terminal connectors onto the new thermostat. Very easy job for someone who is not too handy.

Shut off power at breaker and removed oven door to lessen weight. Removed oven trim and retaining screws and tried pulling out of cabinet. Stuck on power cable, so had to remove Mircrowave oven above to get to power cable plug. Removed oven back cover panel to access thermostat. Easy to unplug and replace with new thermostat. Reassembled and turned on power. Cooked dinner in oven.

Thanks for the excellent service. Parts cheaper than local stores, arrived on time, with NO PROBLEMS.
Installation, probably 30-minutes. Took the opportunity to clean glass, door panels, etc while disassembled, so used about an hour. Oven cleaner was a big help in the cleanup.
Very rewarding project and it saves changing the unit and and refitting the countertop.

Once we figured out to use small allen wrenches in the small holes of the hinge to enable us to lift the door off everything went smoothly. Took out six screws, lifted out the hinges - inserted new ones, replaced screws and replaced door. Yipee

XLarge pizza tray in a 450 degree oven - slam the door & CRACK. Replacement glass arrived on Saturday - VERY FAST DELIVERY. Placed 2 allen wrenches in both hinges - open the door half way & lift up. Place the door on a towel. Removed 6 screws, lift & seperated the inner oven covering, removed the broken glass & cleaned inside & replaced with new glass. More time was spent cleaning & coming up with a tool to fit into the hinge

Repair was fairly simple, unscrewed oven from cabinet and pulled it out. Then remove screws on back panel to access the thermostat location. Unscrew old thermostat, unplug it from connectors and plug in new thermostat. Then screw back in place, replace cover and pop oven back in place. Now fire it up, worked for me! Thanks to part-select. Good luck everyone. Probably saved $200 service call.

Followed a video. Followed instructions

I found that what was keeping the old temp sensor electrical connection attached to the stove-side connection was a little tab. It wasn't obvious that that was the thing that was keeping the connection secure but there weren't any other alternatives. So pushing the tab up with the metal probe (just a narrow rigid metal wire) allowed me to pull the connection apart.

All this takes place way at the back of the oven so its difficult to fiddle with a screwdriver and the retaining screws at arms length. Putting a bit of scotch tape around the screw to keep it attached to the screwdriver kept it from falling off. My hand was a bit shaky extended like that so that was the way to go.

Bottom line, if your oven won't reach or hold the temp you dial in on the control panel it's the temperature sensor. Now if I set it for 300 deg. that's what I get.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

After turning of the breaker for the oven, I pulled out the oven, removed the back panel. The High-Temp thermal cutoff was attached to 2 wires, which I unplugged, and then removed the cutoff by removing two screws. I then replaced the part in reverse order, pushed the oven back into the cabinet, and turned the breaker back on.

removed double wall oven light lens install bulb replace lens fini

Removed old racks, installed new racks. Recycled old racks.

Quickly

Originally ordered just the spring assuming that might be it and it was the cheapest way. However after getting in I found that the latch assembly had a broken 'tit' that is intended to hold the metal latch in place as it moves. Attempted to glue w/ epoxy but as i expected there was too much pressure to hold it in place. So....ordered the assembly.

TURN OFF BREAKER.....

1) Remove the two side rails by removing screw on the inside bottom of rails.
2) It helps to remove the door to get it out of your way but not required. To do this open door fully and insert two nails or similar into holes on each hinge. Close the door until the hinge contact nails. Lift the door up and out.
3) remove the top control panel by removing screw on either side (outside of oven)and screws on the underside of panel behind upper door.
4) It help to completely remove the panel to have more room to work but not required. If you do it is a good idea to photo the cable locations so it is easy to recall where they go. For the most part they only fit one location but always a good idea.
5) remove the latch by removing all spade connectors and two screws in front.
6) place new latch and reassemble.