KEBS177SBL0 KitchenAid Wall Oven - Instructions

The glass caps that cover the bulbs screw out by hand. Then, it was just like changing any other light bulb. I put the caps back on, and magically, we could once again see our food cooking. We had asked other repair companies to replace the bulbs when we had other major work done, but they either didn't want to take the time to get a part number, or didn't want to get it for us. On the PartSelect website, it was easy for us to find and order, not to mention we saved at least $75.00 on the service call alone. Thanks PartSelect!

I found the correct sized light bulb to fit the top portion of my double oven. It fit perfectly and just in time for Thanksgiving.
Thank you Part Select. It was easy to find the right size on your site and my order came in just a few days.

Purchased 2 piece broiler pan from this site

Unscrew the old one, pull it out, along with a few inches of wire. Use a couple of clothes pins to keep the wire escaping back behind the oven as you unhook them from the damaged (bad) one. Then reverse the process with the new one. No big deal. Works great now and the wife is happy.

I didn't. Don't know how to get to light bulb to change it for this specific model

I took the new knob out of the plastic bag and placed it on the oven. The whole process took les than one minute and no tools were needed.

Just slid new rack in. Looks great! Thanks for having just what I needed.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

After 26 years, the element burned out. I followed the diagrams on this website. Basically, I took out the screws that hold the element in place and carefully pulled the old element forward. The wires had fittings that slipped off the old element (with a little help from the wrench.) When the wires were disconnected, I clipped the adjustable wrench on the one of them to make sure they didn't slip back through the holes in the back of the oven. The old fittings slipped right onto the new element (couple of taps with a small hammer to get them all the way on). Them I slipped the wires back through the holes and put the two small screws in the plate at the back of the element. Quite simple, even for a guy with four thumbs.

Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

at first I couldn't get the knob on but after placing a little Vaseline on it, it went right on.

Turned off breaker, verified that the breaker controlled the oven and was actually off.
This is important since you can still get a shock from leaks in the neutral side that may surprize you if you ground one side. Also some breakers can be mislabeled on older homes.
I removed the two screws holding the element to the back of the oven phillips #1 screw driver.
I carefully guided the wires and attached terminals out of the recess until
I had about 5 Inches of wire inside the oven exposed. Just be patient and careful, they will come out.
I then unpluged the wires from the old element and attached a binder clip to the ends so they could not slip back into the oven shell. Clothes pins are also a good choice or some duct tape.
I thoroughly cleaned the oven.
I then installed the wire terminals to the new element and reversed the removal procedure.
I then verified function and temperature of the oven settings.
It took me 10 minutes not including oven cleaning time.

Remove to screws pull old element out, unplugged old element and plugged new element in. Replace screws and baked a cake

Removed the old element and replaced it with the new element. Very straight forward

I googled Kitchenaid along with the model number and Parts Select came up. I then entered the model number along with what I wanted, and scrolled through different pictures until I found a sketch of my cooktop with individual numbers for each part. I selected the part, and rechecked the model number of the cooktop and ordered it. From the time I ordered on-line, until I received it, was 3 days. I am very impressed with the service, and the knob fits perfectly! Thanks so much for the excellent service!