KEBS207DBL11 KitchenAid Wall Oven - Instructions

The repair was very simple. First, turned off the power to the electric oven by turning off the circuit breaker. Removed the side moldings (one screw on the bottom of each), and removed the bottom molding (two screws, one on each side). Removed two screws that held the oven in place (one on each side toward the top). With the help of another person, we pulled the oven out and set it on a two wheel dolly that was laying flat on the floor. I thought I was going to have to remove the power from the wired junction box, but found that the cord was long enough and I could turn the oven on the dolly to get access to the back cover. There are approximately 12 screws that hold on the back most cover. I removed the cover and the thermal shut off was located in the upper left/center part of the back of the oven. I removed the two wires and two screws holding the part to the oven and replaced. I then worked in reverse and put everything back together. The new part fixed the issue and the oven works fine.

first you have to remove door, so open door all the way, pull back the lever on each hinge, then close door all the way, it will be able to be pulled straight out then, but be careful, its a heavy sucker. I layed a blanket out on table and layed door on blanket, start by taking out screws around the edges of door, keep these in separate container.(don't lose any). now you need to separate the door in half, this can be a lil difficult, mine had grease build up on one end that I had to be scraped . pay special attention to how the brackets go and how the door comes apart, this info will be needed later, now that door is in half, you will need to start taking the 2 other layers of glass out, please pay attention how you take apart, it has to be replaced exactly right. take pics if needed. when you get to the broken glass, take out carefully, and place glass over opening, centered well. now you have to start replacing the other layers, the replaced broken glass is kept in place by pressure, once you get the other glass layers in do not lift up door, you will need to put in the screws under the door, one of which tightens the hinge base to the door, these are the screws that tighten the replaced glass, I found this out the hard way and had to undo the whole thing again to recenter the glass, once tight, just keep going backwards replacing the other half of door. once you do this you will either say, wow that stunk, or wow that was easier than I thought. if you don't have patience, then take the door and glass to a repair shop, because you are dealing with 3 pieces of glass costing 50.00 each. be smart.

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long because the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

Replaced hinges since weak springs were allowing the door to open as the oven heated which would turn on the oven light and give a warning on the control panel. To remove door you need to open the dorr all the way and place a short pin through a hole in the hinge under the hinge point. The pin needs to be short enough that you can get it to pass through the door surround. I cut a short pair of pins from a 16D nail. Place the short pins in the respective hinges and then close the door. Grip the oven door handle and the bottom of the door and lift it free of the oven. Lay the door face down on a towel or blanket. remove three phillips screws from the top of the door and two from the brackets on the bottom of the door. Also can remove the two phillips screws on the door that hold each hinge in place. Seperate the door from the glass and lift out the old hinges. Install the new hinges and reassemble the door. ILift the door back into place. Make sure you install it tight/close to the oven front. Open the door, noting any interference and if it opens freely then open completely and remove the factory installed pins from the hinge and you should be done!

You need to replace both the left and right springs. Open the door completely, . Insert a short screw in each pin hole on each spring bracket.slightly lift the door and pull out. remove the four screws that secure the front panel. Remove the four screws that secure the springs. Install the new springs and replace the front panel. Replace the door assembly into the oven, remove the pins that were shipped with the hinges and you are done.

Lower the oven door. Insert the locking hinge pins. Pull the door away from the oven. Remove the 4 screws, 2 at the top and 2 at the bottom, to remove the front panel. Remove the 4 screws that secure each left and right spring. Remove the old springs and install the replacements by reversing the procedure. Remember to purchase 2 springs.

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

First thing- Don't be afraid! It took me way longer to clean the old door parts than to do the actual replacement. First take the door off by opening it fully and sliding a round piece of metal ( I used a 16d nail) in each hinge mechanism. close the door about 3/4 of the way and pull up. Th door comes right off. Just keep undoing screws until you get down to the layer of glass you need to replace, then reverse the process. If you're replacing both the hinges, note that both the pins used to hold the hinge open come out the right side.

Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.

I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new thermostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

The repair went well & the part came in on time for thanksgiving thank you

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

Repair was fast and easy, door closes like new.