KEBS107DBL8 KitchenAid Wall Oven - Instructions

With just the removal of a few screws I was able to replace the glass with the side benefit of cleaning the outter glass that had gotten dirty over the years with use. This is a simple project that all can complete.

removed double wall oven light lens install bulb replace lens fini

After turning of the breaker for the oven, I pulled out the oven, removed the back panel. The High-Temp thermal cutoff was attached to 2 wires, which I unplugged, and then removed the cutoff by removing two screws. I then replaced the part in reverse order, pushed the oven back into the cabinet, and turned the breaker back on.

Quickly

Removed old racks, installed new racks. Recycled old racks.

Removed the door from the oven. Undid all the parts above the inner glass door. Installed the inner glass and reassembled the door. Reinstalled oven door.

Originally ordered just the spring assuming that might be it and it was the cheapest way. However after getting in I found that the latch assembly had a broken 'tit' that is intended to hold the metal latch in place as it moves. Attempted to glue w/ epoxy but as i expected there was too much pressure to hold it in place. So....ordered the assembly.

TURN OFF BREAKER.....

1) Remove the two side rails by removing screw on the inside bottom of rails.
2) It helps to remove the door to get it out of your way but not required. To do this open door fully and insert two nails or similar into holes on each hinge. Close the door until the hinge contact nails. Lift the door up and out.
3) remove the top control panel by removing screw on either side (outside of oven)and screws on the underside of panel behind upper door.
4) It help to completely remove the panel to have more room to work but not required. If you do it is a good idea to photo the cable locations so it is easy to recall where they go. For the most part they only fit one location but always a good idea.
5) remove the latch by removing all spade connectors and two screws in front.
6) place new latch and reassemble.

Several professional appliance repair people told me I had to get a new oven (double, no less!) because "they don't make that hinge anymore." That would have been a $4-5K investment to replace two ovens that both work fine. I'm not generally a DIY person, but was inspired by a FB page I follow called "Handy Women." I got the model number out of my oven, googled "replacement hinge for ____," and found it on this site right away. $120 and about 1 week later I had my hinges. I found this video in the comments on this website that shows (without narration) exactly how to change the hinges.
https://www.youtube.com/watch?v=XzQuU2gZYhk
The only mistake I made that cost me some time had to do with the little pins you have to put into the hinge to remove and replace the oven door. They were missing from the old hinges, and it didn't occur to me to use the ones that were in the new hinges (hadn't unboxed when I started.) I used threaded bolts that were the right diameter and length. They slid right in, but then when I went to take them out, it was an ordeal with WD-40 and an Allen wrench. Then it still didn't occur to me to look at the new ones, so I went to the hardware store and bought two more things the right size without threads. Of course when I took the new hinges out of the boxes they already had the little pins in them. Annoying and time consuming rookie mistake, but my oven door now closes just fine, and I'm getting a ridiculous amount of satisfaction from my little repair job!

Removed the door from oven removed screws from door and replaced the old hinges with new ones perfect match

Followed suggestions from prior Customers that had same problem.

Opened overn door and inserted allen wrenchs through the holes in the door hinges. Close the door until it makes contact with the allen wrenchs, then grasp the oven door handle and the bottom of the oven door and lift up to remove the door. Place the door on a flat surface,(I used a bed) and remove the screws to gain access to the glass. Upon re-assesbly, leave door flat line up and re-install all screws before putting the front pannel back on. Insert door back into the oven and open, remove the allen wrenches and close the door. The process is easy and will take 30 minutes to an hour and save you a $100.00 service call!

Since there is multiple glass panels with several brackets, screws and insulation within the oven door I strongly suggest to take photos at each step using your smart phone. Do not attempt to remove all the components at once. Bracket positions, screw locations and glass orientation is necessary. This is the best advice I have to make this a quick and very easy job.

First we watched a YouTube on how to replace the thermostat. It was easy to turn off the circuit breaker. It was a little tricky to pull the range away from the wall and then we were able to unplug. Because our range is a dual fuel model, the back had a lot more screws to remove to get to the thermostat because there were covers over a lot of wires and the gas line I presume. However, we did get off the 12 or so screws with a regular screw driver. We easily located the thermostat and quickly realized that the two screws holding the thermostat in place were neither flat head nor phillips. We were able to remove one of them and merely twisted it sideways, installed the new thermostat with one screw and attached the wires. When we flipped the circuit breaker and plugged in the over, Voila, it worked. The hardest part was getting all the covers off the back. I hope it doesn't happen again because this was an expensive replacement part.

Read the instructions in installation manual to remove door. Kept removing screws. Was surprised to find two panes of glass between the inner glass and the outer glass. Cleaned all the glass (4) and the inside of the door. Looks brand new. Be careful with the insulation; be sure it is pushed back or it will show from the outside.

Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.