Models > KEBI200VBL0 > Instructions

KEBI200VBL0 KitchenAid Wall Oven - Instructions

Jump to:

All Instructions for the KEBI200VBL0
121 - 135 of 306
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Robert C. from Crisfield, MD
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Oven wouldn't heat. Bake element burned out.
I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. It was that easy. But the people at PartSelect.com were the ones that made it easy; easy ordering and prompt shipment. I got he part in approximately three days. Thanks PartSelect.com. You made me and my wife very happy. We didn't think we were going to have the use of an oven for Christmas. You came through for us.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JERALDINE from MORROW, GA
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake Element Burnt In Half
I removed the two screws that hold the element in place and then I pulled the element out and slid off the contacs and it was disconnected in less than two minutes. When it arrived I installed the new one the same way in less than 2 or 3 minutes and while I waited for thepart to arrive I got a chance to clean my oven and so all is well, I am very pleased with my purchase. It is just that easy and I am happily baking again. Thanks, j. Cale, morrow ga.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Philip from Sunrise, FL
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Lower element would not heat
Removed the retaining plate screws (Phillips), pulled out the element enough to disconnect the wires, disconnected the wires. Installation was the reverse.

btw, PartSelect shipping was phenomenally fast. I ordered this part on Saturday and it was at my door at noon on Tuesday!! Holy Moly...
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dennis from Prairie du Sac, WI
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
oven did not heat
Turn power off, then removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new element, put screws back in and test.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Ann from Cordova, TN
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The bake element had burned in two pieces and would not heat.
With a phillips head screw driver we removed 2 screws pulled out the element about 3 inches and disconnecte the two wires from the insulated connection put the new element in replaced the element in the wall of the oven and replaced the 2 screws. Started the oven and we were good to go.

Part ordered on Monday, delivered on Thursday, put in on Thursday and cooking in no time. Very satisfied customer.
Thanks.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
phillip from prattville, AL
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
faulty heat element
First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
William from Schwenksville, PA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
oven light burnt out
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes
3 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
NINA from CLOVIS, NM
Parts Used:
WP308180
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake element burned out the week before Thanksgiving!
I got online, and "Googled" bake element and Whirlpool (model #), and selected PartSelect by chance. The website had a diagram of my oven with parts and it was easy to select the right part. I paid extra to have it shipped overnight and it arrived the next day. I removed two screws, disconnected the old element, and replaced it with the new element. It worked!! I think I saved a lot of money by doing the repair myself. (I am a 66 yearl old woman and will choose PartSelect by choice for future appliance repairs.)
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Dave from Fairport, NY
Parts Used:
WP308180
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Original Bake Element Failed
Turn off the oven's breaker. Remove oven grates. Unscrew two screws holding in the bake element. Slowly pull the bake element out a few inches. Using pliers, CAREFULLY unattach the connectors from the ends of the bake element. DO NOT FORCE OR CRUSH THE CONNECTORS. Using your hands only, attach the connectors to the ends of the new bake element. Re-insert the element into the back of the oven. Re-insert the screws to attach the new element to the back of the oven. Turn the breaker back on. Turn the oven on bake to test the element. Go have a beer to congratulate yourself on saving $75 or more. Should take about 10 minutes if you're proceeding slowly & carefully. It'll take 2 minutes if you're reckless and get lucky, but it'll take 2+ hours if you're reckless and all goes wrong, causing you screw up the connectors and need to go buy some plus crimpers, etc.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
james from maple plain, MN
Parts Used:
WP308180
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
The lower element was not heating up
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Katherine from Chesterfield, MO
Parts Used:
WP308180
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Baking element was falling apart and not heating up.
I had no instructions, so I started by removing the two screws that seemed to hold the element together. I pulled the element forward and realized I had to seperate the element from the wires. It was an old unit so it took a strong tug but it did come apart. I was hoping at this point I was doing the right thing...I reconnected the new element , pushed it back in and replaced the screws. I was very impressed with myself! The new element heated up in no time. Yeah me!
Thank you "Part Select" for making it possible.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Black Mtn., NC
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
bake element caught fire and burned into
turned power off Unscrewed 2 screws pulled old element out slightly . disconected wires . connected wires to new element tightened 2 screws turned power back on baked a pie. took longer to type this
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Michael from Louisville, KY
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
baking element stopped working
i received the part via fed-x i opened the box uninstalled the old part installed the new part turned it on the element got red hot and it works just fine.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSEPH from ZEPHYRHILLS, FL
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
baking element burned out
Turned off electric to oven by shutting circuit breaker.Opened oven door, took out baking racks,loosened bolts from rear of oven holding element and plate . Disengaged element with plate from wires at rear of oven. Attached new element to clips on wires, rescrewed element plate back to rear wall. replaced racks and turned on circuit breaker. DONE!
Thanks for the quick service ordered one day, next day delivery, never missed a meal or dessert.
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROBERT from GAINESVILLE, VA
Parts Used:
WP308180
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Bake element broke into pieces.
1) Turn off the power at the circuit panel!
2) Remove 2 screws at the back of the bake element.
3) Gently pull the element out about 6 inches.
4) "Unplug" two wires from the back of the element.
5) Do the same in reverse to put the new element back in.
6) Turn the power back on.
7) Done!
0 of 1 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the KEBI200VBL0
121 - 135 of 306