KEBS107DSS8 KitchenAid Wall Oven - Instructions

The repair went well & the part came in on time for thanksgiving thank you

Removed wall oven from wall. Removed back cover. Unscrewed thermastat and removed old thermastat. Screwed in new thermastat and put back together.

Ordered a replacement part and during installation tightened the top mounting screws too tight and shattered the replacement part. Ordered a new replacemnte part and installed without overtighting mounting screws. Repair went well. I caution others not to overtighten top mounting screws. These are same screws that attache the SS pull handle on oven door.

Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.

We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago??

The Kitchenaid oven has 2 interior oven lights. They are behind rectangular glass panels, in an assembly housing The repair is pretty simple. Shut off the power at the breaker box to the oven first. First remove the small screw that holds in the assembly with a Phillips screwdriver. Put down a white piece of paper towel to catch it in case it drops. It is grey color and hard to find against the bottom of the oven. This will free up the assembly and you can move it out. There is a wire on the back so it only comes out a short distance. Next the glass panel covering the bulb must be removed. The small metal clamp with 2 projections that act like a spring to put tension on the glass. Gently pull this out parallel to to the glass and it will release the lens. The old bulb is a simple 2 prong halogen that pulls out easily. Replace it with the new bulb carefully pushing the prongs in. If you did not turn off the power the light will come on immediately. it will get hot quickly so don't touch it for more than a few seconds. Next slide the glass lens back into place into the back of the assembly. Slip the other clip with the screw back on the front. Replace the assembly back into the oven side opening. Secure by replacing the small screw removed in the beginning. You are done. It is about a 5 minute job start to finish. I would replace both bulbs even if only one went out because the other one probably will go out a short time later and you will have to go through this again soon. Oh, and cheap bulbs are not worth it. They are very dim and burn out quickly. Go with the better bulbs you get from PartSelect.

Had no problem replacing the glass it took my Husband and I less than 30 min. It took only a screw driver and that's it. Very easy

The replacement door has a cushion on the top and the sides secured to the tempered glass. When you tighten these brackets they can cause the entire glass panel to break. To prevent this use seven #8 flat washers per hole on the top of the door before securing the brackets. These will act as spacers but you will still will be able to achieve enough pressure to hold everything in place when you tighten them. Hope this helps, it worked for me, florida bob!!

I went to the source of power on the stove and noticed one of the terminals had come loose from the terminal block and had shorted out against the cover of the terminal junction. After prying the loose terminal off cover I ordered new terminal block and received it the 2nd day. I removed the old terminal block and replaced the part in about 10 minutes..Thank you Parts Select for your easy to find diagrams and quick delivery.

I looked up the meaning of the error codes and determined that the temp sensor was malfunctioning. Looked on line for a sensor and found what I thought was the right one and ordered it from PartSelect. The sensor arrived three days later and I removed the old sensor (with some difficulty I might add). Then I discovered the connector did not match. I called PartSelect and found out that the sensor connectors had changed since the oven was built and that an after-market sensor with the right connector was available. I ordered the new one, returned the wrong one and the new one arrived three days later. I popped it in and now I have a working oven.