6644428916 Kenmore Wall Oven - Instructions

replaced light socket but did not repair problem. must have burned the motherboard.


pleased with service from your company.

The hardest part was figuring which breaker controlled the oven because it wasn't marked in my breaker box (it IS now!). So, first I killed all power to the stove, then unscrewed the 2 screws in the back of the oven holding the element. Pulled the element forward, then dissconnected the 2 clampy connector wires (yes, I'm a girl, no correct electrical jargon here). These were a little difficult because my oven is 21 years old & this is the first replacement I've had to do. I reconnected the new element clamps(which was easier), pushed the wires back through the opening & reinserted the screws. Threw the breaker back on, turned on oven to 200 degrees & let heat until the set temperature light turned off as a test. Voila - oven fixed!

First, I removed the oven door by pulling it open to where it loocked and then I pulled it up and off the hinges. Second, I removed the two screws on the top of the door and three screws on the bottom ot the door which allowed me to remove the front of the door. Third, using a nut driver, I removed the frame holding the inner glass to the door and removed that. Fourth, I removed the frame holding the broken glass to the door by removing the screws using my nut driver. I carefully removed the broken glass and vacuumed the channel that had the gasket in it. The gasket was fine so I did not have to replace it and will return it. I placed the glass in the frame on the gasket and reassembled the door in reverse order of how I had disassembled. All went smooth as silk.

We have had our Whirlpool oven for 22 years and became very concerned that a part would not be available. We were thrilled to find the part as well as install the new part ourselves. With a screw driver, we disconnected the old baking element ( be sure to shut the power while doing this) and screwed in the new one. That simple!!!

Removed the retaining plate screws (Phillips), pulled out the element enough to disconnect the wires, disconnected the wires. Installation was the reverse.

btw, PartSelect shipping was phenomenally fast. I ordered this part on Saturday and it was at my door at noon on Tuesday!! Holy Moly...

I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. It was that easy. But the people at PartSelect.com were the ones that made it easy; easy ordering and prompt shipment. I got he part in approximately three days. Thanks PartSelect.com. You made me and my wife very happy. We didn't think we were going to have the use of an oven for Christmas. You came through for us.

I removed the two screws that hold the element in place and then I pulled the element out and slid off the contacs and it was disconnected in less than two minutes. When it arrived I installed the new one the same way in less than 2 or 3 minutes and while I waited for thepart to arrive I got a chance to clean my oven and so all is well, I am very pleased with my purchase. It is just that easy and I am happily baking again. Thanks, j. Cale, morrow ga.

My husband undid the screws of the element. I went to Home Depot and they said I had to order in online. I could not find the part of the Home Depot website, so I googled the part and your business was easy to locate and order the part. It arrived in two days and I, the wife, was able to rescrew the element into place and, voila, the oven was functional again.

FIrst of all I would like to say I was amazed at the quick service we received. I ordered the part at 1:00 pm on a Tuesday and my husband called me at 4:30 on Wednesday that the part had been delivered!! I was amazed.

My husband actually installed the bake element and it only took him a few minutes, the hardest part according to him was actually seperating the prongs of the old piece from the conncetion. Being that our oven is 24 years old could have something to do with that. Everything works just fine.

I am very glad to have found your company on the Web and have told everyone I know about your service.

First I removed the two screws, then I pulled old element out, placed the new element in. Returned the screws in place. Very easy, cheaper to get online than anywhere else and was faster to get the part than anywhere else.

simple replacement

With a phillips head screw driver we removed 2 screws pulled out the element about 3 inches and disconnecte the two wires from the insulated connection put the new element in replaced the element in the wall of the oven and replaced the 2 screws. Started the oven and we were good to go.

Part ordered on Monday, delivered on Thursday, put in on Thursday and cooking in no time. Very satisfied customer.
Thanks.

First I removed the two screws that hold the element in place with a 2' Phillips Head. I then pulled the element out about 3 inches and disconnected the two wires, with nose pliers, since they were semi-hard to remove the male from the female terminals.
I placed the order over the computer and it arrived in 2 days.
I was very pleased with PART SELECT.

Made sure that "Breaker" for oven is in the off positon.

Opened oven door to the first "stay open" position...lifted door straight up...and off of the hinges....which removes the door....and allows easier access to oven.

Removed oven racks

Removed two philips head

Pulled burned out element toward the front of the oven.....exposing the two connector wires.

Used pliers to pull wire connectors from burner element connectors.

Reversed the order of this process....to install new element.

unplugged oven unscrewed old element replaced with new one plugged in oven it only took 2 days to get new element saved time and gas