9114832590 Kenmore Wall Oven - Instructions

This repair was super easy. I removed the two screws holding the oven sensor in place, pulled the sensor from the oven wall to expose the two wires attached to the sensor cut and spliced in the new sensor as per instructions. The supplied wiring kit made this splice very easy. I then reinserted the wires and sensor from the oven wall, put the screws back in place tested the oven. Oven now works like new and I got bonus points from a happy wife!

After getting the part from PartSelect, which only took 2 days to get here and was in great condition and matched perfectly. I went to the customers house, shut off the power to the oven, removed the 2 screws holding in the element, pulled the element out and removed the leads. Took the new element and put the leads on the contacts, pushed the wires and leads back into the hole and screwed in the 2 screws. Went outside and turned the breaker back on, went and turned the oven on to broil, waited a few seconds and it heated up perfectly, and the customer was real happy. She said it was great that she could bake again. Thank you guys for sending the right part in a timely manner and good condition, it keeps my customers happy and keeps me in business. Joe

Shut off power at breaker. Removed two retaining screws, slid out element and unplugged wires, replaced heating element in reverse order. Turned power on and job was complete.

Pulled out old with pliers. Twisted new clips in per instructions.

had two screws to remove from old element, than removed two electric wires from the old element and put the new element back in by putting the wires on the new element and reinstalling the element back in place with two screws and it was done. took about 5 mins. to complete. easy.

When I got the part I removed the tin cover (two screws)on the back of the range. I removed the sensor by removing the two screws inside the oven and pulled out the sensor. taking the instructions advise, I checked the sensor with my ohm meter and although it read 1.1 ohms as compared with the recommended 1.09 ohms at room temperature in the instructions, went ahead and changed the unit. The connector did not fit my particular model so I spliced the wiring and using the two included wire nuts made the connection. I reinstalled the sensor, reattached the gas line, plugged it in and tried the oven before I put it back in place. The oven works great now and it was super easy.

Turned off power to oven. Lifted off the oven door. Removed four 1/4 " bolts from outside of fan housing. Removed two 1/4" bolts holding element. Removed element from three clips holding it to upper oven surface. Unplugged two element wires. Reassembly was the reverse. I am an auto mechanic by trade and this was a fairly simple process.

First of all, go to circuit breaker box and switch off the power to the oven.

Return to oven and verify the power is definitely off.

Open oven door to 'vent' position and remove door. Return hinges to closed position. Remove all racks.

Using nut driver (1/4-inch) remove the two screws just above the element.

Gently rock the element back and forth while pulling gently toward yourself. You should see two wires emerging from the layer of insulation in back of oven. When you have enough wire exposed, use long-nose pliers to gently rock the 'Faston' connectors and pull them off the element's male connectors.

Insert new element and re-install the connectors, being certain they are fully engaged.

Fasten the new element to the back wall of the oven using nut driver. Be careful to not cross-thread - gentle is the word!

Turn the circuit breaker on and very briefly turn the oven to Bake and verify the element is heating. It likely will smoke a bit.

Re-install the racks and the door. Reset the clock.

You should be done and your oven should run for many years..

I tried to unplug old element without success. Called appliance repair man and he pulled part way out, took hold of place where plugged in with pliers and unplugged. While holding back part of plug he plugged in new element--$60.00 later.

The whole job took about 20 min. TURN POWER OFF AT CIRCUIT BREAKER!! Remove 4 screws from the convection cover, then 2 more holding in the broiler element, disconnect 2 wires, and connect to the new one. put the screws back in, the cover back on the convection element and you are done!

Turn off breaker to oven from electrical panel, locatge all screws and remove. Use caution when removing element from clips if not replacing the clips. When removing the element, be careful not to damage connecting wires as they do not pull out very far. Be sure to reattach correctly. When replacing the oven seal, be careful not to disconnect the wires to either element as you slide the oven compartment forward after removing screws. It can be difficult to find the wires behind the oven compartment if they disconnect.