91140169791 Kenmore Wall Oven - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Baking element cracked and would not heat
I turned off the electricity to the oven.and removed the door.
I removed the 2 screws with a nut driver holding the element in place, pulled the element out about 3 inches and disconnected the two wires with pliers , clamped the 2 wires together to keep them from falling in the back of liner.
When the new element was received the procedure was reversed. Electricity was restored and the oven works perfectly.
I removed the 2 screws with a nut driver holding the element in place, pulled the element out about 3 inches and disconnected the two wires with pliers , clamped the 2 wires together to keep them from falling in the back of liner.
When the new element was received the procedure was reversed. Electricity was restored and the oven works perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from Clarkston, MI
- Parts Used:
- WB44K5009
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Broiler element blew out.
- removed the old element
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.
- looked for part number, was none
- could not find direct replacement listed
- compared to dimensions on drawing
- ordered part
- discovered that the mounting plate on new element was too small, holes did not line up, did not cover opening in back of oven.
- sawed off mounting plate on new element
- removed mounting plate from old element
-drilled out holes on old mounting plate to accept new element
- attached the modified element
- Everything works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Corinth, MS
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Bake burned out, checked open with an ohm meter
removed two screws holding the element in place, pulled old element out enough to remove wires that are attached with flag terminals. Installation was in reverse. Turned the oven on and cooked some biscuits. The element that I received from PartSelect was a perfect match.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kay from Roswell, GA
- Parts Used:
- WB44K5013
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Lower Oven Bake Element Burned Out
I should note that my first order to PartsSelect.com
was made on-line and that I selected the wrong part by comparing the burned-out element to the web site picture. When I received that part, I phoned and quickly corrected my mistake, ordered the correct part and obtained return instructions.
With the correct part in hand, I removed the two screws holding the element in place, pulled the element out a short distance to disconnect the two wires and removed the burned-out element. Reversing this procedure I installed the new bake element and completed the job by checking out the oven heating. The hardest part of all this was reaching over the oven door and stretching to unscrew and screw the necessary screws.
was made on-line and that I selected the wrong part by comparing the burned-out element to the web site picture. When I received that part, I phoned and quickly corrected my mistake, ordered the correct part and obtained return instructions.
With the correct part in hand, I removed the two screws holding the element in place, pulled the element out a short distance to disconnect the two wires and removed the burned-out element. Reversing this procedure I installed the new bake element and completed the job by checking out the oven heating. The hardest part of all this was reaching over the oven door and stretching to unscrew and screw the necessary screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from keller, TX
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken element
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, connected new one, put back in place with screws
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tim from fort scott, KS
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Upper over broil unit burned out
This part is a plug-in unit - two screws off; unplug the old unit; plug in the new unit; two screws on. Very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elwood from Allen, MD
- Parts Used:
- WB44K5009
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I researched the part number from partselect.com, ordered it and in less than a week (even in all the snow!) I had my part. Fifteen minutes later, my wife was broiling dinner! I repaired my broiler element without waiting on a repairman and for less than $50.00!
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Replaced the defective element with the new - all inless than fifteen minutes!
Was this instruction helpful to you?
Thank you for voting!
Oven elements were not heating properly.
I had to remove two screws that held these elements in place from back of oven; pull the elements out about three inches to disconnect two wires; connected wires to new elements and
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
replaced two screws.
A very easy job to perform thanks to right parts from PartSelect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Glassboro, NJ
- Parts Used:
- WB44K5013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Element feet broke off and element was laying against botom of oven.
Turned off the power at the panel and then simply removed the two hext screws and unplugged the old element. Plugged in the new element and used a nut driver to relpace the two screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maria from Costa Mesa, CA
- Parts Used:
- WB44K5009
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Broil element
switched off power to oven, unscrewed old broiling unit and installed new one.
Was this instruction helpful to you?
Thank you for voting!
The bake elemement burned out & the clips for the top element were broken
The bake element basically just plugs in remove the two screws in the back with a nut driver pull the element out unplug the spade connectors and reconnect the new element . As far as the clips just snap them on to the top element and snap back in the holes at the top of the oven.
Also very fast delivery less then 48 hours from ordering to delivery
Also very fast delivery less then 48 hours from ordering to delivery
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MARIETTA, GA
- Parts Used:
- WB44K5013
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
New element had blade connectors (male).
Drilled small holes in blades to accept existing machine screws from oven wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HAROLD from Tucson, AZ
- Parts Used:
- WB21X5301
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Just follow the enclosed instructions
Followed the instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CASPER, WY
- Parts Used:
- WB21X5301
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Bad sensor
By myself
Was this instruction helpful to you?
Thank you for voting!